mirror of
https://github.com/LiBwrt-op/ipq50xx.git
synced 2025-12-16 23:12:30 +00:00
55c46cbabd
Hardware Spec
-SoC: Rockchip RK3588S
CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
-RAM: 64-bit 4GB/8GB LPDDR4X at 2133MHz
-Flash: 32GB/None eMMC, at HS400 mode
-Ethernet: one Native Gigabit Ethernet, and one PCIe 2.5G Ethernet
-USB: one USB 3.0 Type-A and one USB 2.0 Type-A
-PCIe: one M.2 Key M connector with PCIe 2.1 x1
-HDMI:
compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
support up to 7680x4320@60Hz
Support RGB/YUV(up to 10bit) format
-microSD: support up to SDR104 mode
-GPIO:
30-pin 2.54mm header connector
up to 1x SPI, 3x UARTs, 3x I2Cs, 2x SPDIFs, 1x I2Ss, 3x PWMs, 20x GPIOs
-Debug: UART via 3-Pin 2.54mm header, or on-board USB-C to UART
-LEDs: 4 x GPIO Controlled LED (SYS, WAN, LAN, LED1)
-others:
2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS
MASK button for eMMC update
one user button
-Power supply: USB-C, support PD, 5V/9V/12V/20V input
-PCB: 8 Layer, 62x90x1.6mm
-Ambient Operating Temperature: 0℃ to 70℃
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
eMMC Installation:
Boot from the SD card
Uncompress the OpenWrt sysupgrade image
fash to eMMC : dd if=*.img of=/dev/mmcblk1
sync
remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
45 lines
1.2 KiB
Plaintext
45 lines
1.2 KiB
Plaintext
|
|
. /lib/functions/leds.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
|
|
board=$(board_name)
|
|
boardname="${board##*,}"
|
|
|
|
board_config_update
|
|
|
|
case $board in
|
|
friendlyarm,nanopi-r2c|\
|
|
friendlyarm,nanopi-r2c-plus|\
|
|
friendlyarm,nanopi-r2s|\
|
|
friendlyarm,nanopi-r4s|\
|
|
friendlyarm,nanopi-r4s-enterprise|\
|
|
xunlong,orangepi-r1-plus|\
|
|
xunlong,orangepi-r1-plus-lts)
|
|
ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth0"
|
|
ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth1"
|
|
;;
|
|
friendlyarm,nanopi-r5c)
|
|
ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1"
|
|
ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0"
|
|
ucidef_set_led_netdev "wlan" "WLAN" "green:wlan" "phy0-ap0"
|
|
;;
|
|
friendlyarm,nanopi-r5s)
|
|
ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth0"
|
|
ucidef_set_led_netdev "lan1" "LAN1" "green:lan-1" "eth1"
|
|
ucidef_set_led_netdev "lan2" "LAN2" "green:lan-2" "eth2"
|
|
;;
|
|
friendlyarm,nanopi-r6c)
|
|
ucidef_set_led_netdev "wan" "WAN" "wan_led" "eth0"
|
|
ucidef_set_led_netdev "lan1" "LAN1" "lan1_led" "eth1"
|
|
;;
|
|
friendlyarm,nanopi-r6s)
|
|
ucidef_set_led_netdev "wan" "WAN" "wan_led" "eth1"
|
|
ucidef_set_led_netdev "lan1" "LAN1" "lan1_led" "eth2"
|
|
ucidef_set_led_netdev "lan2" "LAN2" "lan2_led" "eth0"
|
|
;;
|
|
esac
|
|
|
|
board_config_flush
|
|
|
|
exit 0
|