The RTL931x devices have an other register that describes the
current RAM configuration. Enhance the identification routine.
Tested on LGS352C (RTL9311).
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19284
Signed-off-by: Robert Marko <robimarko@gmail.com>
Until now the rt-loader only works on U-Boot driven devices where the
environment (e.g. coprocessor) is usually setup properly. Devices like
the ZyXEL GS1920 series use BootBase as start environment and skip
some of the basic initialization steps. rt-loader will fail in these
cases. Take care about the CP0 registers.
Additionally enhance the documentation of the printf implementation.
It was optimized during the different revisions of the initial PR.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19253
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are too many supported Realtek devices so avoid activating the
rt loader recipe in the default builds. Just start with the LGS310C.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18397
Signed-off-by: Robert Marko <robimarko@gmail.com>
To make use of the new rt-loader provide the needed recipes.
This has been tested with the following devices:
- rtl838x Linksys LGS310: initramfs & flash
- rtl930x Zyxel XGS1210: initramfs
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18397
Signed-off-by: Robert Marko <robimarko@gmail.com>
The bootloader of many Realtek switches only supports gzipped kernel images.
With limited flash space that might get critical in future versions. For better
compression allow support for compressed images. For this a new loader was
developed. Several ideas have been taken over from the existing lzma loader
but this has been enhanced to make integration simpler. What is new:
- Loader is position independent. No need to define load addresses
- Loader identifies device memory on its own
- Loader uses "official" upstream kernel lzma uncompress
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/lib/decompress_unlzma.c
- Loader uses "official" UNMODIFIED nanoprintg that is used by several
bare metal projects. https://github.com/charlesnicholson/nanoprintf
Compiled the loader ist just under 12KiB and during boot it will show:
rt-loader
Found RTL8380M (chip id 6275C) with 256MB
Relocate 2924240 bytes from 0x80100000 to 0x8fce0000
Extract kernel with 2900144 bytes from 0x8fce521c to 0x80100000...
Extracted kernel size is 9814907 bytes
Booting kernel from 0x80100000 ...
[ 0.000000] Linux version 6.12.33 ...
[ 0.000000] RTL838X model is 83806800
...
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18397
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move changes to mt7988a.dtsi from patch adding the support for the
MT7988A Reference Board to a dedicated patch to ease maintainance.
Fixes: f9206d1111 ("kernel/mediatek: 6.12: replace downstream files by patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Restore the conversion to an all-UBI NAND layout and use of fitblk on
SPI-NAND connected via the mt65xx SPI controller.
Apply the same also for SPI-NAND connected via the SNFI controller, and
use fitblk also for boot from SPI-NOR, eMMC and SD.
Fixes: f9206d1111 ("kernel/mediatek: 6.12: replace downstream files by patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MediaTek MT7988A RFB currently hangs on boot as CCI fails to probe.
This is due to the wrong SoC compatible string "mediatek,mt7988" instead of
"mediatek,mt7988a". Fix that.
Fixes: f9206d1111 ("kernel/mediatek: 6.12: replace downstream files by patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
During setup the mdio driver decides the polling mode of the 4 smi
busses depending on the DTS phy settings. This works as follows:
- set polling to c45 if at least one phy is ethernet-phy-ieee802.3-c45
- set polling to c22 if all phys are ethernet-phy-ieee802.3-c22
On RTL930x it is not possible to switch to c22 if uboot has set c45
before. Fix this by overwriting the bitfield properly. While we are
here:
- Sort variables according to kernel style (inverse christmas tree)
- Initialize fields properly with = { 0 }
- Use GENMASK() for better readability
- Make use of RTMDIO_MAX_SMI_BUS
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19161
Signed-off-by: Robert Marko <robimarko@gmail.com>
This will allow more flexibility in using PHY drivers as kmods.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
After update to v6.12 some PCS driver fixes were dropped and additional
are needed due to updated driver.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
The original PCS driver did not use the .pcs_validate() in
phylink_pcs_ops. The patches for 1000/2500base-x and 10g modes were
taken from this old driver, and thus did not bother with
.pcs_validate(). Thus, even though these modes are supported, phylink
would not enable them.
To fix these, list these modes in .pcs_validate(). Also list them in
ipq_pcs_clk_rate_get(). While the latter does not appear to change
behavior, it does change the clock rates listed under
/sys/kernel/debug/clk
Co-developed-by: Mantas Pucka <mantas@8devices.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
0102-arm64-dts-qcom-ipq9574-Fix-USB-vdd-info.patch was merged in 6.12.34
Other patches automatically refreshed.
Fixes: cb1b656027 ("kernel: bump 6.12 to 6.12.34")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/19232
Signed-off-by: Robert Marko <robimarko@gmail.com>
When using TFTP install method on a fresh unit, wifi_fw and ubi_rootfs UBI volumes must be removed or will hang when mounting.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/19215
Signed-off-by: Robert Marko <robimarko@gmail.com>
As a workaround to an issue causing hang during PCI enumeration on
imx8mp with a specific PCIe switch, disable PCI AER.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19189
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable DT overlay support:
- add dt-overlay to board features
- add DEVICE_DTS_OVERLAYS
- update the boot script to resize before applying each overlay
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19189
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport some additional upstream patches:
- 6.13-arm64-dts-imx8mm-venice-gw73xx-remove-compatible-in-overlay-files.patch
(this resolves some issues when using dt overlays on gw73xx-0x)
- 6.16-PCI-imx6-Skip-link-up-workaround-for-newer-platforms.patch
- pending-PCI-imx6-Remove-apps_reset-toggle-in-_core_reset-function
(these resolve enumeration issues on imx8mm/imx8mp with a pcie switch)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19189
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification:
SoC: MediaTek MT7628NN
RAM: 128 MB, EtronTech EM68C16CWQG-25H (DDR2)
Flash: 32MB, Winbond 25Q256JVFQ (Dual Boot, SPI)
Switch: MediaTek MT7628AN, 4 ports 100 Mbps
WiFi: MediaTek MT7603 2T2R/2.4GHz 802.11n
GPIO: 3 buttons (Wi-Fi, Reset, FN), 3 LEDs (Power, Internet, Wi-Fi), 1 port USB 2.0
Disassembly:
At the bottom, under the LEDs, there are 2 screws hidden by rubber feet. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it.
Serial Interface:
The serial interface can be connected to the 5 pin dots located on the right between the operating mode switch and the antenna.
Pins (from antenna to operating mode switch):
VCC
TX
RX
NC
GND
Settings: 115200, 8N1
Flashing via OEM recovery software:
1. Download the OEM recovery software from the manufacturer's website
2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1212_recovery.bin
3. Replace the file in the fw folder OEM recovery software with the file from step 2.
4. Run the OEM recovery software and follow the instructions.
Flashing via TFTP:
1. Connect your PC and router to port 1-3, configure PC interface using IP 192.168.1.2, mask 255.255.255.252
2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1212_recovery.bin via TFTP
3. Power up the router while pressing Reset button on the back
4. Release Restart button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image.
When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/19157
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Until now the timer management on the RTL931x devices depends
on the MIPS default timer. Looking at the clock progress on
these devices one can see that it is totally off. It is running
at half the required speed (e.g. if 1 minute passes the date
command shows that according to the timers only 30 seconds have
elapsed). This is a mix from wrong DTS and bad startup code.
This is not only a cosmetic issue but has effects on every
delay operation inside the kernel. Switch RTL931x to the proven
Otto timer.
Tested on LGS352C based on RTL9311.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19205
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Otto timer is very helpful on the RTL931x devices.
Include it into the builds.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19205
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream has gained support for forced affinity settings in the MIPS
GIC interrupt controller. This is needed to enable the Otto timer on
the RTL931x platform. See
https://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git/
commit/?id=2250db8628a0d8293ad2e0671138b848a185fba1
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19205
Signed-off-by: Robert Marko <robimarko@gmail.com>
Check Point V-80 (Quantum Spark 1590 Appliance) is an Appliance, based
on Armada 8040 (88F8040).
Specification:
- SoC : Marvell Armada 8040 (88F8040)
- RAM : DDR4 2 GiB (4x 512 MiB chip)
- Flash : eMMC 4 GiB
- Ethernet : 10x 10/100/1000 Mbps
- LAN 1-8 : Marvell 88E6393X
- WAN : Marvell 88E1512
- DMZ : Marvell 88E1512 (RJ-45/SFP combo)
- LEDs/Keys (GPIO): 11x/1x
- UART : "CONSOLE" port (USB 1.1 Type-C)
- chip : Silicon Labs CP2102N
- port : ttyS0
- settings : 115200bps 8n1
- HW Monitoring : 2x nuvoTon NCT7802Y
- USB : USB 3.0 Type-A
- Power : 12 VDC, 3.3 A
- plug : DC Plug 2.5/5.5 mm (inner/outer)
Flash instruction (common):
1. Boot V-81 normally
2. Login to the vendor CLI (default: admin/admin) and login to the Linux
CLI by `expert` command
3. Update U-Boot environment variables by the following commands
fw_setenv bootcmd_ow_usb 'usb start; load usb 0:1 ${loadaddr} boot.scr && source ${loadaddr}'
fw_setenv bootcmd_ow_sd 'load mmc 0:1 ${loadaddr} boot.scr && source ${loadaddr}'
fw_setenv bootcmd_ow_emmc 'run set_mmc_internal; mmc read ${loadaddr} ${prim_header_mmc_blk} 4 && source ${loadaddr}'
fw_setenv bootcmd 'run bootcmd_ow_usb; run bootcmd_ow_sd; run bootcmd_ow_emmc; run bootcmd_part${activePartition};'
Attention: don't forget single quatations of values to prevent
expansion of variables
4. Turn off the device
Flash instruction (USB-boot/SD-boot):
1. Extract and burn (squashfs|ext4)-sdcard.img.gz to USB storage or
MicroSD card
2. Connect that storage to V-81
3. Turn on V-81 and it will be booted with OpenWrt in that USB storage
Flash instruction (eMMC-boot):
1. Copy initramfs image, dtb and bootsctipt to the USB storage with
renaming
initramfs.bin -------> Image
dtb -----------------> armada-8040-v-81.dtb
bootscript (.scr) ---> boot.scr
2. Connect that storage to the USB 3.0 port on V-81
3. Turn on V-81 and it will be booted with OpenWrt initramfs image in
that USB storage
4. Upload (squashfs|ext4)-sysupgrade.gz to V-81
5. Perform sysupgrade with the uploaded image
6. Wait ~100 seconds to complete flashing
Reverting to stock firmware:
1. Turn on V-81 and interrupt booting by Ctrl + C
2. Select "4. Restore to Factory Defaults (local)"
3. Wait ~180 seconds to complete restoring and rebooting
Notes:
- The partition table in the internal eMMC has single partition, but
"blkdevparts=" parameter will be passed from the bootloader and that
definition will be used instead.
- The port-side LED pairs of RJ-45/SFP ports on V-81 are switched by a
GPIO pin of pin7 on &cp0_gpio2. (High(1): RJ-45, Low(0): SFP)
This needs to be switched manually.
- The MicroSD card slot is too unstable and the following messages are
printed without "marvell,xenon-phy-slow-mode;" property.
[ 97.060851] mmc0: error -84 whilst initialising SD card
[ 97.137049] mmc0: error -84 whilst initialising SD card
[ 97.214315] mmc0: error -84 whilst initialising SD card
...
- There are no detailed information about maximum power consumption
limit of the SFP port or optional DSL-SFP modules sold officially.
But the power requirement of almost DSL-SFP modules are 3.3V/700mA, so
set the maximum value of the SFP port to 2000 mW (Power Level III).
- Do not insert a MicroSD card before turning of the device when OpenWrt
installation. The stock firmware deletes all files in the first
partition automatically, to use it as a storage for logs.
MAC addresses:
LAN: 00:1C:7F:xx:xx:FA (mmcblk1boot0, ethaddr (text))
WAN: 00:1C:7F:xx:xx:F9 (mmcblk1boot0, eth2addr (text))
DMZ: 00:1C:7F:xx:xx:FB (mmcblk1boot0, eth1addr (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Check Point V-80 (Quantum Spark 1550 Appliance) is an Appliance, based
on Armada 7040 (88F7040).
Specification:
- SoC : Marvell Armada 7040 (88F7040)
- RAM : DDR4 2 GiB (4x Nanya NT5AD512M8D3-HR)
- Flash : eMMC 4 GiB (Toshiba THGBMNG5D1LBAIL)
- Ethernet : 6x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6352
- WAN : Marvell 88E1512
- LEDs/Keys (GPIO): 6x/1x
- UART : "CONSOLE" port (USB 1.1 Type-C)
- chip : Silicon Labs CP2102N
- port : ttyS0
- settings : 115200bps 8n1
- HW Monitoring : 2x nuvoTon NCT7802Y
- USB : USB 3.0 Type-A
- Power : 12 VDC, 3.3 A
- plug : DC Plug 2.5/5.5 mm (inner/outer)
Flash instruction (common):
1. Boot V-80 normally
2. Login to the vendor CLI (default: admin/admin) and login to the Linux
CLI by `expert` command
3. Update U-Boot environment variables by the following commands
fw_setenv bootcmd_ow_usb 'usb start; load usb 0:1 ${loadaddr} boot.scr && source ${loadaddr}'
fw_setenv bootcmd_ow_emmc 'run set_mmc_internal; mmc read ${loadaddr} ${prim_header_mmc_blk} 4 && source ${loadaddr}'
fw_setenv bootcmd 'run bootcmd_ow_usb; run bootcmd_ow_emmc; run bootcmd_part${activePartition};'
Attention: don't forget single quatations of values to prevent
expansion of each variables
4. Turn off the device
Flash instruction (USB-boot):
1. Burn (squashfs|ext4)-sdcard.img.gz to USB storage
2. Connect that storage to the USB 3.0 port on V-80
3. Turn on V-80 and it will be booted with OpenWrt in that USB storage
Flash instruction (eMMC-boot):
1. Copy initramfs image, dtb and bootsctipt to the USB storage with
renaming
initramfs.bin -------> Image
dtb -----------------> armada-7040-v-80.dtb
bootscript (.scr) ---> boot.scr
2. Connect that storage to the USB 3.0 port on V-80
3. Turn on V-80 and it will be booted with OpenWrt initramfs image in
that USB storage
4. Upload (squashfs|ext4)-sysupgrade.gz to V-80
5. Perform sysupgrade with the uploaded image
6. Wait ~100 seconds to complete flashing
Reverting to stock firmware:
1. Turn on V-80 and interrupt booting by Ctrl + C
2. Select "4. Restore to Factory Defaults (local)"
3. Wait ~180 seconds to complete restoring and rebooting
Notes:
- V-80 has some HW versions. Internal MicroSD card slot and mPCIe slot
is available on some HW versions, but not on the other HW versions.
confirmed (MicroSD/mPCIe slots):
- 1.0.1: unavailable
- 1.0.3: available
- The partition table in the internal eMMC has single partition, but
"blkdevparts=" parameter will be passed from the bootloader and that
definition will be used instead.
MAC addresses:
LAN: 00:1C:7F:xx:xx:4B (mmcblk1boot0, ethaddr (text))
WAN: 00:1C:7F:xx:xx:4A (mmcblk1boot0, eth1addr (text))
Tested-by: Yanase Yuki <dev@zpc.st>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add image-specific signature support to Build/boot-scr.
This is required to switch root devices passed to the kernel on Check
Point V-80 and V-81.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable "emmc" feature to use the emmc helpers on sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable CONFIG_CMDLINE_PARTITION symbol to use "blkdevparts=" parameter
support on Check Point V-80.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Expose the sysfs interface to userspace tools for power monitoring.
Useful for tracking energy usage in CPU package, cores, DRAM, etc.
Build system: x86/64
Build-tested: x86/64
Run-tested: x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/18255
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix the status indicator light of the LAN port.
Signed-off-by: jinkela air <air_jinkela@163.com>
Link: https://github.com/openwrt/openwrt/pull/19135
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This device is similar to the Cudy TR3000 v1 128MB version.
The difference is that the flash memory is 128mb and the other is 256mb
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 256 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Power: 5 VDC, 3 A
Installation:
Cudy has distributed intermediate firmware to make installation easier
1. Go to [Cudy CN official website](https://www.cudy.com/zh-cn/pages/download-center/tr3000-1-0) and download the intermediate firmware
2. Upgrade the intermediate firmware on the page
3. Visit the intermediate firmware 192.168.1.1 webpage and use the sysupgrade image to update
other:
If you fail to flash the device, you can use TFTP to flash back to the original firmware.
1. Ask Cudy CN official customer service for the original firmware
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an recovery.bin firmware file.
Signed-off-by: cheng wang <typedelta@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19167
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove all files etc. for 6.6 because 6.12 is default now.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19139
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use Linux 6.12 as default for all subtargets.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19139
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. For
this device it is only a substitution of the existing DTS configuration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. For
this device it is only a substitution of the existing DTS configuration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. For
this device it is only a substitution of the existing DTS configuration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. For
this device it is only a substitution of the existing DTS configuration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
REMARK! The original commit c829bc1f2c ("realtek: Add support for
Netgear S350 series switches GS308T and GS310TP") says that the SFP
ports are untested. Looking at device internal pictures from
https://techinfodepot.shoutwiki.com/wiki/Netgear_GS310TP there are no
external phys for the SFP ports. So fix port description.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the new INTERNAL_PHY_SDS() helper to describe the SFP ports. With
this change the driver now knows that ports 24/26 are driven by serdes
4/5.
For the RTL838x devices this is currently only an additional information
for the mdio bus. It is not evaluated further because everything is
hardcoded.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
