Add missing kmod-7915e package to get both wireless interfaces working.
Link: https://github.com/openwrt/openwrt/issues/18690
Reviewed-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Reduces boot time by 3s on a freshly installed image. This device
has a large flash and the gain can be higher with more packages
installed. According to the datasheet, this is the maximum frequency
supported by the Micron and Macronix chips that are installed in
these devices. Tested on three units over a two month period.
Before:
$ dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
1+0 records in
1+0 records out
10485760 bytes (10 MB, 10 MiB) copied, 1.51901 s, 6.9 MB/s
After:
$ dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
1+0 records in
1+0 records out
10485760 bytes (10 MB, 10 MiB) copied, 0.899474 s, 11.7 MB/s
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/18694
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
-----------------------------------------------------------
Vendor-UI Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs.trx image.
2. Connect the PC via LAN to one of the yellow router ports and wait
until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1
4. If your router is brand new, finish the setup process and log into
the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the
downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
-----------------------------------------------------------
TFTP Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to rtax52.bin.
2. Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax52.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
---------------------------------------------------------------------------
Revert to stock firmware:
1: Download the rt-ax52 firmware from ASUS official website. Save
the firmware to tftp server directory and rename to RT-AX52.trx
2: Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
3: Conect to the serial console, power on again, interrupt the
autoboot process by pressing '4' when prompted.
$: ubi remove linux
$: ubi remove jffs2
$: ubi remove rootfs
$: ubi remove rootfs_data
$: ubi create linux 0x45fe000
$: reset
Then the dut will reboot,interrupt the autoboot process by
pressing '2' when prompted.
2: Load System code then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
$: enter y
you will see the follow, type enter directly:
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (RT-AX52.trx) ==:
4: wait for the device run up
Based on support for ASUS RT-AX52 by liudongdongdong7397
and trx image generation by remittor
Signed-off-by: Christoph Krapp <achterin@gmail.com>
This commit fixes mistaken executable bit on
mt7981b-mercusys-mr80x-v3.dts file.
Fixes: 7921e48d43 ("mediatek: add support for Mercusys MR80X v3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Prevent flashing truncated or otherwise corrupted uImage.FIT images
by verifying checksums and hashes of all sub-images before flashing
using the newly packaged fit_check_sign tool.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add all boards using uImage.FIT to platform_check_image() case section
making sure we are dealing with a FIT image.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The WL-WN573HX3 is an AX3000 outdoor Access Point by WAVLINK,
also sold in Europe as 7Links WLR-1300 (ZX-5612).
Specifications:
- MT7981B + MT7976 AX3000 2x2 DBDC (160 MHz)
- 16 MiB SPI NOR, 256 MiB RAM
- Gigabit ethernet port, 802.3af PoE
- IP67 outdoor case for wall or pole mounting with
four single band RP-SMA fiberglass antennas (8 dBi)
Installation:
- OEM Web UI is at 192.168.30.1 which will forward to
http://netlogin.link (using a captive portal)
- login with default password `admin`
- skip setup wizard by navigating directly to
http://netlogin.link/html/meshUpgrade.html
- upload WN573HX3-sysupgrade.bin
- reset to factory defaults to discard OEM UCI settings
MAC address assignment:
LAN 80:xx:xx:76:xx:25 hw 0x44e
WLAN 2.4G 80:xx:xx:76:xx:27 factory 0x04 (label MAC)
WLAN 5G 82:xx:xx:46:xx:27
pair key 8a:xx:xx:76:xx:27 also on label, not used by OpenWrt
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
This commit adds support for Mercusys MR80X(EU) v3 router.
Device specification:
- SoC: Mediatek MT7981b, Cortex-A53, 64-bit
- RAM: 512MB
- Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
- Ethernet: 4x 100/1000 Mbps LAN1,LAN2,LAN3 & WAN
- Wireless: 2.4GHz (802.11 b/g/n/ax)
- Wireless: 5GHz (802.11 a/n/ac/ax)
- LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs
on ethernet ports
- Buttons: 1 (Reset)
- Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Installation (UART):
- Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2
- Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'.
- Set the uboot environment for startup.
setenv tp_boot_idx 0; setenv bootcmd bootm 0x46000000; saveenv
If the bootarg is set to boot from ubi1, also change it to ubi0.
- Load and run OpenWrt initramfs image.
setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm
- Browse IP 192.168.1.1, upload the 'sysupgrade' image and do upgrade.
Recovery:
- Press Reset button and power on the router.
- Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware.
Stock layout:
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format:
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 94:0C:xx:xx:xx:12 | label |
| WAN | 94:0C:xx:xx:xx:13 | label+1 |
| LAN | 94:0C:xx:xx:xx:12 | label |
| WLAN 2g | 94:0C:xx:xx:xx:11 | label-1 |
| WLAN 5g | 94:0C:xx:xx:xx:10 | label-2 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac".
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18181
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: M16U4G16256A DDR4 512MB
Ethernet: 2x 2.5G + 3x 1G
USB: 1x USB 3.0
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
Download initramfs image, reboot router,
waiting for tftp recovery to complete.
After openwrt boots up, perform sysupgrade.
Note:
Back up all mtd partitions before flashing.
Signed-off-by: Yujie Zhu <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18138
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
**Huasifei WH3000 eMMC / Fudy MT3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC.
MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
**Enlarging a partition**
Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space.
```
sgdisk -p /dev/mmcblk0
```
```
Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 14942174
Partitions will be aligned on 1024-sector boundaries
Total free space is 11197 sectors (5.5 MiB)
Number Start (sector) End (sector) Size Code Name
1 8192 9215 512.0 KiB 8300 u-boot-env
2 9216 13311 2.0 MiB 8300 factory
3 13312 21503 4.0 MiB 8300 fip
4 21504 29695 4.0 MiB 8300 config
5 29696 62463 16.0 MiB 8300 kernel
6 62464 4256767 2.0 GiB 8300 rootfs
7 4257792 14940159 5.1 GiB 8300
```
You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6`
```
sysupgrade -F /tmp/openwrt-initramfs-kernel.bin
```
Install and run cfdisk
```
opkg update && opkg install cfdisk
cfdisk /dev/mmcblck0
```
- Select `mmcblck0p7` -> Delete
- Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit
You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`.
Co-developed-by: hecatae <horus.ra@gmail.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18220
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Only force compat_version to 1.2 if it was less than 1.2 before, as changes
1.1 and 1.2 were bootloader-related and a completed boot indicates that the
changes have been completed. Newer compat version 1.3 indicates a config change
and should not be forced on boot.
Fixes: 84fc59c0d5 ("mediatek: filogic: bpi-r3: set netdev-name for sfp1 port")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add 'ubootmod' variant for the ASUS ZenWiFi BT8.
An out-of-tree installer will be provided in Github to allow users an easy
transition from the stock loader to OpenWrt's bootchain which is built from
source.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Break out all flash-layout dependent parts from device tree into separate
dtsi file to be used by both, stock layout and upcoming ubootmod variant.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
MediaTek MT7988D SoC (3x Cortex-A73 @1.8 GHz max)
1GB DDR4 RAM
128MB SPI-NAND (Winbond)
MediaTek MT7996 BE14000 Tri-Band Wi-Fi 7
3x LAN (2x 1GE MT7988 built-in, 1x 2.5GE MaxLinear GPY211C)
1x WAN (2.5GE MT7988 built-in)
LED: RGB PWM (supported as 3x PWM LED)
USB: 1x USB 3
Buttons: RESET, WPS
UART: 115200 8N1 3.3V
Installation
------------
1. Hold down RESET button and power on the device until
LED pulses red.
2. Assign IP 192.168.1.70/24 to your computer's Ethernet port
3. Connect Ethernet to one of the 1GE LAN ports
4. Open browser and visit http://192.168.1.1
5. Upload openwrt-mediatek-filogic-asus_zenwifi-bt8-factory.bin
6. Once OpenWrt initramfs system comes up, do sysupgrade using
openwrt-mediatek-filogic-asus_zenwifi-bt8-squashfs-sysupgrade.bin
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
arcadyan_mozart was incorrectly placed below asus devices
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18331
Signed-off-by: Robert Marko <robimarko@gmail.com>
This can be used by GL.iNet devices from other target.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove a stray '|' character from 01_leds which has accidentally
been added.
Reported-by: Chukun Pan <amadeus@jmu.edu.cn>
Fixes: 63d56af6c6 ("mediatek: filogic: migrate Netgate N60 to upstream PHY LED control")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Other than GPIO LEDs, PHY LEDs do have an address.
Fix node names such that all gpio-leds do *not* contain an '@' sign and
PHY leds which do have an address also do contain the '@' sign.
This is done to prevent more copy&paste'ry of non-complaint DT
fragments.
Fixes: 7cbe34170e ("mediatek: add support for the GL.iNet GL-MT3000")
Fixes: fe10f97439 ("filogic: add support for GL.iNet GL-MT6000")
Fixes: e8f7597317 ("mediatek: filogic: add support for Cudy RE3000 v1")
Fixes: c9cb6411c1 ("mediatek: add support for Cudy WR3000 v1")
Fixes: 7560af7647 ("mediatek: filogic: migrate ASUS TUF AX6000 to upstream PHY LED control")
Fixes: 25ea7ff393 ("mediatek: filogic: migrate Acer W6/W6d to upstream PHY LED control")
Fixes: d50d51d74e ("mediatek: filogic: migrate Zyxel NWA50AX Pro to upstream PHY LED control")
Fixes: b88de5d507 ("mediatek: filogic: migrate Zyxel EX5700 to upstream PHY LED control")
Fixes: 63d56af6c6 ("mediatek: filogic: migrate Netgate N60 to upstream PHY LED control")
Fixes: fd76a38190 ("mediatek: filogic: migrate SmartRG Bonanza to upstream PHY LED control")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All devices have already been migrated to the upstream PHY LED
API. This prevents users from adding new devices using this hack.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
With upstream changes hitting kernel 6.4 the dtb for u7623 ends up with
both mac (gmac) disabled, since this is now the default status in
mt7623.dtsi. Fix this by including mt7623a.dtsi (which already has all
necessary bits) and enabling all revlevant ports. This will also do
a side hustle of assigning proper clocks for power controller and
specifying proper power domain for few devices.
Link: https://lore.kernel.org/all/20230210182505.24597-1-arinc.unal@arinc9.com
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250304164507.60511-2-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
RTL8261N is used on some Airoha and Realtek devices. Move the driver
from Mediatek to generic so it can be used everywhere.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18163
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
fixed wrong reg.
The original commit assumed the size part was the end of the reg.
Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Boyang Sun <boyinthesun@163.com>
Link: https://github.com/openwrt/openwrt/pull/18074
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The OpenWrt One is the only board listing kmod-nvme as part of it's
default package set.
Remove kmod-nvme from the default package set as the board is sold
without an NVMe SSD and the M.2 slot can also be used for other
purposes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This makes it possible to initialize the eMMC from scratch like it is
done for the BPI-R3 mini (without an SD card).
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This board is also as known as SuperElectron ZN-M5 and ZN-M8. However,
for ZN-M5 and ZN-M8, there's another version uses ZX279128 as CPU
chip, which is unsupported.
You can check it in "高级设置" > "系统日志" > "内核日志" page from webUI.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS
Power: DC 12V 1A
Stock layout flash instructions:
Login into webUI and upload sysupgrade firmware in "系统管理" > "升级固件" page.
Remember to unselect "保留配置" ("Keep configurations") first before doing that.
OpenWrt U-Boot layout flash instructions:
1. Flash stock layout firmware first.
2. Connect to the device via SSH, and backup everything,
especially 'Factory' partition.
3. Unlock MTD partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18121
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
I selected one subtarget after the other and refreshed their
configuration using this command:
make kernel_oldconfig CONFIG_TARGET=subtarget
For MT7629 I had to re-add CONFIG_LEDS_SMARTRG_LED manually.
Otherwise, building MT7629 with ALL_KMODS we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot
compilation. See commit 6bdea8c7bd ("mediatek: mt7629: 6.6: disable
LEDS_SMARTRG_LED by default") for more details.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
btmtk.ko is used by btusb.ko and btmtkuart.ko, add it into an own
package and make both packages depend on it.
Fixes: 1c42a0be36 ("kernel: modules: bluetooth: separating UART and USB drivers")
Link: https://github.com/openwrt/openwrt/pull/18110
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
