The patch adding temperature sensor support for r8169 has been removed upstream
and the functionality will be added to Realtek PHY instead:
1f691a1fc4
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This was the first DSA packaged, and the tagger was made into
a separate package. This is too complicated: the mv88e6xxx
is the only module using this tagger after all, fold the module
for the DSA hardware and the driver for the tagger into a
single package and let modprobe do its job of probing the
tagger for the driver.
Tested on the BMIPS Inteno XG6846.
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250110-mv88e6xxx-single-package-v1-1-223ad7fb312e@linaro.org/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This LED controller has a driver under development which is currently being reviewed by the respective kernel maintainers. They are currently on v11 which is included here.
The LED1202 is a 12-channel low quiescent current LED driver with:
* Supply range from 2.6 V to 5 V
* 20 mA current capability per channel
* 1.8 V compatible I2C control interface
* 8-bit analog dimming individual control
* 12-bit local PWM resolution
* 8 programmable patterns
If the led node is present in the controller then the channel is
set to active.
The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17451
Signed-off-by: Robert Marko <robimarko@gmail.com>
7a3bcd39ae1f r8169: use helper r8169_mod_reg8_cond to simplify rtl_jumbo_config
e3e9e9039fa6 r8169: align WAKE_PHY handling with r8125/r8126 vendor drivers
330dc2297c82 r8169: improve rtl_set_d3_pll_down
c507e96b5763 r8169: improve __rtl8169_set_wol
83cb4b470c66 r8169: remove leftover locks after reverted change
2cd02f2fdd8a r8169: improve initialization of RSS registers on RTL8125/RTL8126
a3d8520e6a19 r8169: align RTL8126 EEE config with vendor driver
4af2f60bf737 r8169: align RTL8125/RTL8126 PHY config with vendor driver
eb90f876b796 r8169: align RTL8125 EEE config with vendor driver
b8bd8c44a266 r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats
f75d1fbe7809 r8169: add support for RTL8125D
c4e64095c00c r8169: enable EEE at 2.5G per default on RTL8125B
d64113c6bb5e r8169: remove rtl_dash_loop_wait_high/low
1c105bacb160 r8169: avoid duplicated messages if loading firmware fails and switch to warn level
ac48430368c1 r8169: don't take RTNL lock in rtl_task()
e3fc5139bd8f r8169: implement additional ethtool stats ops
b8bf38440ba9 r8169: enable SG/TSO on selected chip versions per default
854d71c555df r8169: remove original workaround for RTL8125 broken rx issue
1ffcc8d41306 r8169: add support for the temperature sensor being available from RTL8125B
The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.
The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix bogus reference to kmod-nf-conntrack-timeout, fixing the warning
`WARNING: Makefile 'package/kernel/linux/Makefile' has a dependency on
'kmod-nf-conntrack-timeout', which does not exist`.
Fixes: 0e2dcfc4f4 ("netfilter: add kmod-nfnetlink-ct{helper,timeout}")
Signed-off-by: Joel Low <joel@joelsplace.sg>
Link: https://github.com/openwrt/openwrt/pull/17388
Signed-off-by: Robert Marko <robimarko@gmail.com>
Package bnxt_en kernel module for Broadcom NetXtreme-C/E based Ethernet
network chips like BCM573xx and BCM574xx.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17301
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 1cea889c96.
This reverts commit 5fd86d66c1.
The patch is causing build servers to fail. Revert it for now.
Signed-off-by: John Crispin <john@phrozen.org>
This option enables support for monochrome LEDs that are grouped into multicolor
LEDs which is useful in the case where LEDs of different colors are physically
grouped in a single multi-color LED and driven by a controller that doesn't have
multi-color support.
Signed-off-by: Jonathan Brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16397
Signed-off-by: John Crispin <john@phrozen.org>
This commit adds the Linux kernel mainline driver "leds-ktd202x" for the
KinetIC KTD2026 and KTD2027 RGB/RBGW controller with I2C interface that was
introduced in kernel version 6.7, last changed in mainline on 2024-05-31.
At least the Acer Connect Vero W6m (a variant of the Acer Predator Connect
W6 without 2.5G eth1 port, usb3 port, and the 6 on-board gpio RGB LEDs) is
equipped with a KTD2026 (and a single RGB LED attached to it used by the
stock firmware as status LED), and maybe other router devices also are.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change the dependency on the kmod-media-controller from depends to
select.
Fixes: 1095925246 ("kernel: add kmod-media-controller dependency for kmod-usb-audio")
Link: https://github.com/openwrt/openwrt/pull/17058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Netatalk v4 reintroduces AppleTalk and this module is required for
layer 3 protocol support.
Module was removed in kernel 4.14 for OpenWrt 18.06 (commmit
14a0131, 22/02/2018). At the time nothing used it as Netatalk v3
did not support AppleTalk.
Not building ipddp feature/module like it was in the past, as
recommended by upstream Netatalk maintainers.
Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16979
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These packages are needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The snd-usb-audio drivers uses media controller if media controller is set.
So add kmod-media-controller as dependency.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disable drm-i915 module for target x86/geode.
Fixes: 77cfe8f ("x86: make i915 as a kmod with required firmware")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16977
Signed-off-by: Robert Marko <robimarko@gmail.com>
i915 driver requires to load correct firmware to work on latest x86
GPU, it is more reasonable to make it as a kernel module, so that
initramfs is not required, and it can also save some space from the
kernel image comparing being a built-in driver
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/16276
Signed-off-by: Robert Marko <robimarko@gmail.com>
Package kmod-drm-panel-mipi-dbi as well as modules it depends on in
order to support a wide range of MIPI DBI complaint SPI-connected
TFT panels.
See https://github.com/notro/panel-mipi-dbi/ for more information on
how to use specific panels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Package gs_usb CAN driver, which is for Geschwister Schneider and
bytewerk.org candleLight compatible USB/CAN interfaces.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Drop limitation on depending on only armv8 for armsr target as those
module should support both 32 and 64 bits systems.
Only thunderx-net actually require 64 bit systems.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add INET diag socket monitoring interface module for MultiPath TCP.
It allows using native Linux socket diagnostic tools such as 'ss' for
Multipath TCP connections.
Co-authored-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
Signed-off-by: sKy King <29267720+sKyissKy@users.noreply.github.com>
Link: https://github.com/openwrt/openwrt/pull/12884
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set the boot flag for the igc, mlx4-core, and mlx5-core network device drivers
to load them at a more early stage of the boot process.
This is required for network drivers whose network interface PCI paths are set
via ucidef_set_network_device_path inside the 02_network script since it is
called after kernel modules are loaded from modules-boot.d but before they are
loaded from the modules.d directory.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16560
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The swconfig-based b53 driver for the BCM53128 switch stopped working
after commits b2cfed48f6 (Revert "swconfig: fix Broadcom b53 support")
and e4e410733f (kernel: export switch_generic_set_link() symbol). This
rendered the 8 LAN ports of the EdgeSwitch 8XP non-functional, so the
image compilation for the device was disabled (5a1d7d8c1b).
This commit adds the kmod-dsa-b53-mdio and kmod-dsa-b53 packages
with the upstream B53 DSA driver, replacing the swconfig-based
kmod and kmod-switch-bcm53xx-mdio downstream ones that are not used by
any other device.
The 8 LAN ports of the EdgeSwitch 8XP are usable again. The 02_network
init script has been updated with the new DSA interfaces lan1 .. lan8.
Image building has been reenabled for the device, adding the usual DSA
incompatibility notice.
Tested on a Ubiquiti EdgeSwitch 8XP.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Link: https://github.com/openwrt/openwrt/pull/11680
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This solution that is needed for some routers to provide proper
LED activity when controlled directly by the MV88E6xxx switch,
has just been merged in upstream Linux.
Make this patch 901 as other backports from earlier kernels
are in patch 896 and this is the first free number after
that.
Patch offsets in pending patches are augmented as part of
the refresh.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
RmNet driver provides a transport agnostic MAP (multiplexing and
aggregation protocol) support in embedded module. Module provides
virtual network devices which can be attached to any IP-mode
physical device.
This is commonly used on Qualcomm based modems for data aggregation.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
1. Remove outdated symbol CONFIG_USB_OHCI_ATH79.
The ath79 OHCI USB was already supported by the generic driver
kmod-usb-ohci. And this kernel symbol has been dropped since
upstream commit:
53d473fc1e38 ("usb: host: Remove the deprecated ATH79 USB host config options")
2. Add ath79 USB phy package to the OHCI dependencies.
Both EHCI and OHCI require it on the ath79 target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Compile LED support to swconfig and phy modules
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building DSA switch drivers as kernel modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building multiple phy drivers as kernel modules
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building both upstream and downstream ag71xx drivers
as modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Adds the x86_64 dependency for mlxsw_core
* Removes the redundant mlxsw_core dependency
from mlxsw-minimal and mlxsw-spectrum
* Removes the DCB configuration symbols because
they were moved into the generic configuration
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the missing x86 dependency for
the Mellanox mlxcpld LED driver.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6.1.103 and 6.6.44 introduced breakage complaining about missing mtd_test.ko
for some targets.
Signed-off-by: Zxl hhyccc <zxlhhy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16093
Signed-off-by: Robert Marko <robimarko@gmail.com>
Compilation of mtd_test.ko should be added only for kernel 6.6 or above.
Fixes 26df88a ("kernel: Add kmod-mfd-test")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16085
Signed-off-by: Robert Marko <robimarko@gmail.com>
6.6.44 introduced breakage complaining about missing mtd_test.ko
for some targets.
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16061
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the package for the Pixart PAC7302 USB Camera Driver kernel module.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package the sctp_diag.ko file which already gets build when kmod-sctp
and kmod-inet-diag are selected.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Package the mfd-core.ko kernel module. It is selected by the
kmod-hwmon-gsc already.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The mtd_nandbiterrs.ko kernel module was added with kernel 3.7. We
should package it like the other test modules.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
kxxhash_generic.ko is a soft dependency of kmod-fs-btrfs, but we did not
package it. Extract the kmod-lib-xxhash and then package
xxhash_generic.ko.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The kmod-fs-btrfs package has a soft dependency to kmod-crypto-blake2b
The CONFIG_BTRFS_FS kernel build option selects CONFIG_CRYPTO_BLAKE2B,
but we did not package it before.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The kernel provides two variants of the lz4 compression a normal version
and a high compression mode version. The old kmod-lib-lz4 package
contained the normal version plus one part of the lz4hc version. There
was already code which selected the kmod-lib-lz4hc package which did
not exists.
I split this into 3 packages. kmod-lib-lz4 and kmod-lib-lz4hc for the
normal the and high compression algorithm which contain the specific
code and the kmod-lib-lz4-decompress which contains the common
decompressor.
New we are also packaging lz4hc.ko
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The nf_dup_ipv4.ko and nf_dup_ipv6.ko kernel module were packaged by
kmod-ipt-tee and kmod-nft-dup-inet at the same time. Extract them into a
separate package used by both.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch for G761 PWM Fan controller support. This is used by
an ipq807x RAX120v2 and have an internal clock that was currently
unconfigured making the device not working.
Link: https://github.com/openwrt/openwrt/pull/15796
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It has its own dedicated knob
Signed-off-by: Nathaniel Wesley Filardo <nwfilardo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15761
Signed-off-by: Robert Marko <robimarko@gmail.com>
New dependencies required for the module to be useful, and correct IPv6 support
Signed-off-by: Nathaniel Wesley Filardo <nwfilardo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15761
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 'kmod-stmmac-core' package is referenced by the following packages:
* kmod-dwmac-intel
* kmod-dwmac-imx
* kmod-dwmac-sun8i
The problem is that 'kmod-of-mdio' is not selectable for 'TARGET_x86'.
That means the package 'kmod-dwmac-intel' is not available on this
architecture and so the package 'kmod-dwmac-intel' could not be enabled.
To fix this remove the dependencies 'kmod-of-mdio' from 'kmod-stmmac-core'.
This is not needed on this level, because the modules 'kmod-of-mdio' is
already selected by the packages 'kmod-dwmac-imx' and 'kmod-dwmac-sun8i'.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Commit ae8bf1a26e ("imx: add imx8m support") configured the
drm-imx-ldb kmod for imx_cortexa9 and imx_cortexa7 however it is only
applicable to imx_cortexa9 (imx6).
Fix this so that we can avoid a missing module config for cortexa7 when
moving to the 6.6 kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
There are too many RTC drivers in other.mk, they deserve their
own menu and .mk-file, so let's break them out to a separate
entity.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Split the kmod-video-dma into kmod-video-dma-sg and
kmod-video-dma-contig. The old one contained two kmods, but sometimes
only one of them is build which caused problems. The configuration
options are not manually selectable in the kernel and hidden in OpenWrt.
Currently this causes build failures on some targets.
Fixes: 4d7cbe0a55 ("kernel: video-dma: explicitly state packaged modules")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Because wildcard in variable stating packaged modules, the filtering for
built-in kernel modules didn't work and would cause a packaging failure.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
At least kmod-fb-tft depends on CONFIG_FB_DEVICE and can not be
activated without it.
This configuration option was added with kernel 6.6, before this featre
was always activated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds a new mlxreg package, which allows access
to Mellanox programmable device register space through sysfs
interface for thermal control and hardware management.
It also adds required Mellanox I²C drivers and packages
for the "special" MSN4800 series and SN2201 platform.
Signed-off-by: Til Kaiser <mail@tk154.de>
The IXP4xx is well supported upstream and can readily be
supported with kernel v6.6. To simplify things after the
DTS directory was renamed, switch to v6.6 only.
Bring in some outstanding patches.
Tested on the Gateworks GW2348-4.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Allow kmod-acpi-video to be built for loongarch64:
The x86-specific CONFIG_ACPI_WMI will be split from default
kmod-acpi-video as a board-specific addition.
* Allow kmod-drm-amdgpu to be built for loongarch64:
Also add loongarch64-specific configs and modules.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This adds a kernel module package for the Marvell
MV88E6XXX DSA switch and a separate module package for
the DSA tagger since it can in theory be used by multiple
DSA switches. Enable both DSA and EDSA tags in the
tagger.
We can't just compile this in because just a few devices
has this DSA, and it depends on e.g. the I2C and SFP
to be loaded as modules first.
We have no examples of DSA switches being packaged as
modules before, all seem to be compiled in, but it
actually works just fine to do this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This module supports the Microchip Technology Inc (SMSC)
EMC2301/EMC2302/EMC2303/EMC2305 fan speed PWM controller chips.
Signed-off-by: Oleg S <remittor@gmail.com>
Historically it's possible to leave the `SUBTARGETS` undefined and
automatically fallback to a "generic" subtarget. This however breaks
various downstream scripts which may have expectations around filenames:
While some targets with an explicit generic subtarget contain `generic`
in the filenames of artifacts, implicit "subtargets" don't.
Right now this breaks the CI[1], possibly also scripts using the ImageBuilders.
This commit removes all code that support implicit handling of
subtargets and instead requires every target to define "SUBTARGETS".
[1]: https://github.com/openwrt/openwrt/actions/runs/8592821105/job/23548273630
Signed-off-by: Paul Spooren <mail@aparcar.org>
Include the CONFIG_KVM_SMM option in the kvm-x86 package to enable system management mode emulation on KVM.
Co-authored-by: Stefan Hellermann <stefan@the2masters.de>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Fix error: Package kmod-lan743x is missing dependencies for the following libraries:
fixed_phy.ko
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Kernel 6.2 folded virqfd (eventd interface for VFIO interrupts)
into the base vfio module, it is no longer a tristate option.
Change suggested by vincejv on GitHub:
https://github.com/openwrt/openwrt/pull/14868#issuecomment-1998260124
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Add imx8m support:
- add a cortexa53 subtarget to imx
- move ARCH and KERNELNAME to subtargets
- account for kernel modules that are not used for cortexa53
No device-specific targets or firmware images are created yet but all
imx8m* dtbs will be built.
enabling CONFIG_TARGET_ROOTFS_INITRAMFS results in
openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin which has been
successfully booted on an imx8mm-evk using the following:
u-boot=> tftpboot $fdt_addr_r image-imx8mm-evk.dtb && \
tftpboot $kernel_addr_r openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin && \
booti $kernel_addr_r - $fdt_addr_r
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
enable support for RK35xx in kmod-ata-ahci-platform kernel module
Suggested-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Build and package driver for MediaTek PCIe 5G WWAN modem T7xx device
available in Linux 6.1 and 6.6 as kmod-mtk-t7xx.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
drm-amdgpu and drm-radeon require drm-exec and/or drm-suballoc-helper in
6.6, so since we have them packaged separately include them when required.
Fixes: 5b08b56007 ("kernel: modules: video: adapt for kernel 6.6")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linux 6.4 has split out the previously AMDGPU specific suballocation
helper into a generic one and it has its own symbol now.
So, lets package it as a separate helper as AMDGPU still requires it
for 6.6.
Signed-off-by: Robert Marko <robimarko@gmail.com>
As part of adding kernel 6.6 support, DRM_EXEC and DRM_SUBALLOC_HELPER were
added to the kmod-drm, however these are only used by drm-amdgpu and
drm-radeon which are only supported on x86.
So, lets start fixing building of other targets by removing these from the
main kmod-drm, in follow-up commits they will be packaged separately and
selected when required.
Fixes: 5b08b56007 ("kernel: modules: video: adapt for kernel 6.6")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Many can kernel modules are now gated by the newly introduced
CONFIG_CAN_NETLINK configuration option. Activate it to build the can
drivers again.
This was changed in this upstream Linux commit:
https://git.kernel.org/linus/df6ad5dd838e0fa543ca28ca6154901fa65a9443
This should fix these warnings with kernel 6.1 and 6.6:
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-c-can is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-c-can-pci is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-c-can-platform is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-mcp251x is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-slcan is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-8dev is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-ems is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-kvaser is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-peak is not available in the kernel config - generating empty package
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
