realtek: Fix block comment style

In net code, it is preferred to have block comments which

* either are one line: `/* ... */`
* multiple lines with:
  - starting with the first comment line directly: `/* ...`
  - each line is intended with the first asterisk: ` * ...`
  - the last line is just the end of the comment:  ` */`

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://github.com/openwrt/openwrt/pull/20906
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

target/linux/realtek/files-6.12/drivers/net/dsa/rtl83xx/qos.c

@@ -251,7 +251,8 @@ static void rtl839x_rate_control_init(struct rtl838x_switch_priv *priv)
 	/* Set default burst rates on all ports (the same for 1G / 10G) with a PHY
 	 * for UC, MC and BC
 	 * For 1G port, the minimum burst rate is 1700, maximum 65535,
-	 * For 10G ports it is 2650 and 1048575 respectively */
+	 * For 10G ports it is 2650 and 1048575 respectively
+	 */
 	for (int p = 0; p < priv->cpu_port; p++) {
 		if (priv->ports[p].phy && !priv->ports[p].is10G) {
 			sw_w32_mask(0xffff, 0x8000, RTL839X_STORM_CTRL_PORT_UC_1(p));

target/linux/realtek/files-6.12/drivers/net/dsa/rtl83xx/rtl838x.c

@@ -511,11 +511,13 @@ static void rtl838x_l2_learning_setup(void)
 {
 	/* Set portmask for broadcast traffic and unknown unicast address flooding
 	 * to the reserved entry in the portmask table used also for
-	 * multicast flooding */
+	 * multicast flooding
+	 */
 	sw_w32(UNKNOWN_MC_PMASK << 9 | UNKNOWN_MC_PMASK, RTL838X_L2_FLD_PMSK);
 
 	/* Enable learning constraint system-wide (bit 0), per-port (bit 1)
-	 * and per vlan (bit 2) */
+	 * and per vlan (bit 2)
+	 */
 	sw_w32(0x7, RTL838X_L2_LRN_CONSTRT_EN);
 
 	/* Limit learning to maximum: 16k entries, after that just flood (bits 0-1) */
@@ -1115,7 +1117,8 @@ static int rtl838x_write_pie_action(u32 r[],  struct pie_rule *pr)
 	 * they have different precedence depending on their type and this precedence
 	 * defines which Action Information Field (0-4) in the IACL table stores
 	 * the additional data of the action (like e.g. the port number a packet is
-	 * forwarded to) */
+	 * forwarded to)
+	 */
 	/* TODO: count bits in selectors to limit to a maximum number of actions */
 	if (pr->fwd_sel) { /* Forwarding action */
 		data = pr->fwd_act << 13;

target/linux/realtek/files-6.12/drivers/net/dsa/rtl83xx/rtl838x.h

@@ -885,7 +885,8 @@ enum egr_filter {
 /* Intermediate representation of a  Packet Inspection Engine Rule
  * as suggested by the Kernel's tc flower offload subsystem
  * Field meaning is universal across SoC families, but data content is specific
- * to SoC family (e.g. because of different port ranges) */
+ * to SoC family (e.g. because of different port ranges)
+ */
 struct pie_rule {
 	int id;
 	enum pie_phase phase;	/* Phase in which this template is applied */

target/linux/realtek/files-6.12/drivers/net/dsa/rtl83xx/rtl839x.c

@@ -556,7 +556,8 @@ static void rtl839x_l2_learning_setup(void)
 {
 	/* Set portmask for broadcast (offset bit 12) and unknown unicast (offset 0)
 	 * address flooding to the reserved entry in the portmask table used
-	 * also for multicast flooding */
+	 * also for multicast flooding
+	 */
 	sw_w32(UNKNOWN_MC_PMASK << 12 | UNKNOWN_MC_PMASK, RTL839X_L2_FLD_PMSK);
 
 	/* Limit learning to maximum: 32k entries, after that just flood (bits 0-1) */

target/linux/realtek/files-6.12/drivers/net/dsa/rtl83xx/rtl930x.c

@@ -1472,11 +1472,11 @@ static void rtl930x_get_l3_nexthop(int idx, u16 *dmac_id, u16 *interface)
 
 
 // Currently not used
-// /* Creates an interface for a route by setting up the HW tables in the SoC
+// /* Creates an interface for a route by setting up the HW tables in the SoC */
 // static int rtl930x_l3_intf_add(struct rtl838x_switch_priv *priv, struct rtl838x_l3_intf *intf)
 // {
 // 	int i, intf_id, mtu_id;
-// 	/* number of MTU-values < 16384 *\/
+// 	/* number of MTU-values < 16384 */
 
 // 	/* Use the same IPv6 mtu as the ip4 mtu for this route if unset */
 // 	intf->ip6_mtu = intf->ip6_mtu ? intf->ip6_mtu : intf->ip4_mtu;