This board is also as known as LC-HX3001
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: Foresee F35SQA001G 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain SSH access:
Method 1:
1. Connect UART Adapter to the router
2. UART pins are enabled, set the root password with passwd command
start the dropbear instance on port 22
Method 2:
1. Login into web interface, and restore the router with SSH enabled configuration.
2. After reboot Default Web interface password will be 12345678
SSH password is empty
Flash instructions:
1. Connect to HX21, backup everything, especially 'Factory' part.
3. Write new FIP:
mtd write openwrt-mediatek-filogic-hx_21-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
8. To write new BL2
Install mtd-rw
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd write openwrt-mediatek-filogic-imou_hx21-preloader.bin bl2
Signed-off-by: Jahidul Islam <hello@jahid.io>
Link: https://github.com/openwrt/openwrt/pull/20753
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to the factory uboot and firmware[1], the ubi size is set
to 512 MiB (0x20000000) and it exceeds the size of the flash, after
that the uboot and kernel resizes it to 114.5 MiB (0x7280000) instead
of 114.125 MiB (0x7220000). The mismatch of the ubi size causes
kernel fails to read ubi volumes and throws panic.
Trim whitespaces while at it.
1. https://github.com/immortalwrt/immortalwrt/issues/2123#issuecomment-3523744128
Fixes: c908fc7d95 ("mediatek: add support for Zbtlink ZBT-Z8102AX v2")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20769
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header hole on PCB
- 3.3V, RX, GND, TX (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber/Blue)
1x Wi-Fi (Amber/Blue)
1x WAN activity (Amber/Blue)
4x LAN activity (Amber/Blue)
- Power : 12VDC, 1A (Center positive polarity)
Note: The LED color is amber or blue, depending on your router's color
(black/white).
MAC address
-----------
+-----------+-------------------+-----------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------+
| WLAN 2.4G | B0:38:6C:xx:xx:xx | label |
| WLAN 5G | B2:38:6C:4x:xx:xx | |
| WAN | B0:38:6C:xx:xx:xx | label + 1 |
| LAN | B0:38:6C:xx:xx:xx | label + 3 |
+-----------+-------------------+-----------+
The WLAN 2.4G MAC address was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software (ipTIME Firmware Wizard (11ac))
from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router (keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router (LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Limitation: Triggering the WLAN LED for activity on both phy0 (2.4GHz) and phy1 (5GHz)
----------
Currently, the UCI doesn't support triggering a single LED for activity
on multiple WLAN interfaces. As a temporary workaround, the LED is
configured to only indicate activity on `phy1`. If you wish to monitor
`phy0` instead, you must change the device from `phy1-ap0` to `phy0-ap0`
in the LuCI LED configuration.
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20771
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Teltonika RUTC50 has a 5G modem. Install uqmi by default to control the
modem with the default package set.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add mt7987-2p5g-phy-firmware to DEVICES_PACKAGES of the MT7987A RFB as
well as the BananaPi R4 Lite.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The ports are physically labelled in reverse order on the device.
This patch aligns logical names with physical ones.
LED order on front of device is correct after this patch.
Fixes: 9d66b8b312
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/20528
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for TP-LINK BE450.
Device specification
--------------------
SoC Type: MediaTek MT7988D, Cortex-A73, 64-bit
RAM: 512MB
Flash: SPI NAND GigaDevice (128 MiB)
Ethernet: MediaTek MT7531AE (3 Ports) + 2.5GbE (internal MT7988 phy) + 10GbE (RTL8261N)
WLAN: MT7992
WLAN 2g: MediaTek MT7975N, b/g/n/ax/be, MIMO 4x4
WLAN 5g: MediaTek MT7979N, a/n/ac/ax/be, MIMO 4x4
LEDs: 8 LEDs, 1 status blue, 2x WIFI blue, 2x Internet
blue/orange, 1 LAN blue, 1 usb blue, 1 wps blue, gpio-controlled
Button: 2 (Reset, WPS)
USB port: Yes
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2023.10-rc4. Additionally, ubi0
partition contain "seconduboot" (also U-Boot 2023.10-rc4)
Serial console (UART), unpopulated, located near the power connector
---------------------
heatsink
| |
| |
| | +----+-----+------+-------+ +-----------------+
| | | TX | RX | GND | +3.3V | | power connector |
+---+ +----+-----+------+-------+ +-----------------+
|
Don't connect ----+
Disassemble: rm the 2 screws at the bottom and the one at the backside.
un-clip the case starting at the edge above the LEDs.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot 0x50000000 openwrt-mediatek-filogic-tplink_be450-initramfs-kernel.bin && bootm 0x50000000
4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Note: the 10GbE (RTL8261N) is only working if reverting this Realtek target specific commit:
b77fa45d12
The second ubi partition (ubi1) is empty and there is no known
dual-partition mechanism, neither in u-boot nor in the stock firmware.
NMBM is not used.
Not Working: WED, if activated, MT7992 isn't recognized any more.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/20398
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Also the MT7987 RFB accidentally already set the not-yet-existing
mt798x-2p5g-phy-firmware-internal package as one of the DEVICE_PACKAGES.
This currently breaks the build, so remove it for now. Also remove stray
'blkid' package from DEVICE_PACKAGES which was accidentally copied from
MediaTek's SDK.
Fixes: 9de7189ed4 ("mediatek: build image for MT7987 RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Because the firmware has not yet been accepted in linux-firmware we
cannot yet package mt7987-2p5g-phy-firmware-internal. Remove it from
DEVICE_PACKAGES of the BPi-R4-mini until the an upcoming linux-firmware
release will come with this firmware included, allowing us to then
create that package.
Fixes: 8b6c6978d6 ("mediatek: add support for BananaPi BPi-R4 Lite")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit fixes mistaken executable bit on dts files.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20676
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The BPi-R4 Lite is a WiFi-7 router board based on the MT7987 SoC.
Specification :
- SOC: Mediatek MT7987A (4x Cortex-A53
- RAM: 2GB
- Flash: 32MB SPI NOR, 256MB SPI NAND, 8GB eMMC
- Switch: MediaTek MT7531AE
- Ports : 4x LAN (1G), 1x SFP (via MT7531), 1x WAN (2.5G)
- Buttons : Reset & WPS/Mesh
- LEDs : Status (PWM), SFP
- USB: on-board VIA VL817 USB3.1/USB2.0 hub
* 1 - mPCIe B (SIM3)
* 2 - NGFF-KEYB (SIM1)
* 3 - USB-A connector
* 4 - mPCIe A (SIM4)
- mPCIe: 1x 8GT/s x2 or 2x 8GT/s x1 (configurable via bootloader)
- RTC: PCF8563
- mikroBUS socket with SPI, I2C and full UART
- on-board HT42B534 USB-to-serial for Type-C console port
- Power: USB Type-C PD 20V, or DC via barrel connector or JST-VH 3.96
Installation:
Uncompress *sdcard.img.gz and write to microSD card, eg. using 'dd'.
Use bootloader menu on the serial console to install SPI-NAND or SPI-NOR,
once installed to SPI-NAND you can use the bootloader menu to install to
eMMC. See instructions for BananaPi R3 for details.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import and clean DT and DT-overlay files from MediaTek's SDK to build
an image with various DT-overlays for the MT7987 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patches to use cpufreq voltage calibration data from the efuse on
MT7988, and add support for MT7987.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MT7987 has two LVTS thermal sensors, one covering all CPU cores,
and one for the built-in 2.5GE PHY.
Add support for MT7987 to the LVTS thermal driver.
Thanks to Chad Monroe of Adtran for providing cleaned up patches for
Linux 6.6 which have been ported to Linux 6.12.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Compared to MT7988 (NETSYSv3) the Ethernet Frame Engine of MT7987
has been slighly updated (NETSYSv3.1), among other things the packet
scheduler (shaper) has apparently been reworked.
Import patches for basic support of the Ethernet Frame Engine of the
MT7987 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MT7987 is mostly a stripped-down low-pin-count version of the
MT7988 without the 10GBit/s SerDes. Most existing drivers can be reused.
Import to-be-sent-upstream patches doing all the groundwork for
basic support for the MT7987 SoC, adding clk, pinctrl and pwm support.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix Totolink X6000R image failing to upgrade via sysupgrade due to an
incorrect upgrade case. The fallback upgrade path used the NAND upgrade
routine, which caused the "layout volume not found" error on NOR flash
devices. By adding a specific case for this board, sysupgrade now uses
`default_do_upgrade`, which is compatible with the NOR flash layout.
Fixes: 7cd10ad
Signed-off-by: Ayra Hikari <ayrahikari@linuxmail.org>
Since 6b43a52171, the PHY is using interrupts instead of polling. It
turned out that the interrupt number is wrong and the WAN port doesn't
work. This commit fixes this bug.
Fixes: 6b43a52171 ("mediatek: mt7622: add the missing phy interrupt-parent for WAX206")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This board is also as known as E-Life ETR631-T/ETR635-U.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20357
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport phylink patches for PCS/PHY caps OPs. This makes it easier to
align future generic PCS patch and permit supporting special PHY that
needs specific tune if "in-band" mode is enabled (for example Aeonsemi
PHYs)
This is also mainly using the upstream version of the Mediatek patch
739-net-add-negotiation-of-in-band-capabilities.
All affected patch automatically refreshed.
Link: https://github.com/openwrt/openwrt/pull/20461
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These devices only have one SPI peripheral. And the chip select pin is
directly controlled by the SPI host hardware. Hence we don't need to
assign empty GPIO phandle for them. This patch also adjust the reg
address of the SPI peripheral node to follow the cs-gpios changes.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The imagebuilder is not intended to build initramfs images. Some
profiles attempt to do this and succeed, due to buildroot leaking
the initramfs-kernel into staging_dir; others attempt it, but fail
due to not having initramfs binaries present in the imagebuilder.
Fix this by adding an explict guard around the unsupported generation
of the initramfs images. This saves space and time during imagebuilder
runs, fixes those that are currently broken and protects against future
breakage for profiles that inadvertently work now.
Fixes: https://github.com/openwrt/openwrt/issues/20151
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20347
Signed-off-by: Robert Marko <robimarko@gmail.com>
the eth1 interface was renamed to wan so also reflect that change in
the leds setup script
Fixes: f26260c7e7 ("mediatek: filogic: Add label wan and cpu for Zyxel EX5601-T0")
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20120
Signed-off-by: Nick Hainke <vincent@systemli.org>
Continuous reading mode is broken for some spi controllers. There are two
possible bug scenarios:
1) "continuous mode" flash and spi controller without dirmap support,
but with restriction on transfer length in adjust_op_size()
2) "continuous mode" flash and spi controller with dirmap support for a
single flash page
In the first case, any read that exceeds the limit specified in adjust_op_size()
will result in an EIO error. The limit may even be less than a size of a single
flash page. In this case, any read will result in an error.
In the second case, any read larger than flash page size will result in an EIO
error or spinand driver spoofing (because the spi controller driver returns
more bytes than were actually read).
This patch series tries to fix continuous reading (spinand driver side).
Unfortunately these fixes can't resolve "spinand driver spoofing" case.
Spi controller drivers might need fixes as well.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20295
Signed-off-by: Robert Marko <robimarko@gmail.com>
Should be reset-gpio. Also added GPIO_ACTIVE_HIGH for clarity.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
The former is deprecated. Fixes dtc warning.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
The latter is more descriptive in terms of what's going on.
Mostly found with
git grep gpios\ | grep 0\>
git grep gpios\ | grep 1\>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
The former is deprecated. Fixes dtc warning.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
Point the driver to the precal section of the emmc "factory" partition.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/20154
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace the hotplug script with nvmem now that loading data from emmc
partitions is supported.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/20154
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Avoids the occacial lost race, where VAPs are created before the hotplug
script has updated the phy mac address.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/20154
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add missing bluetooth support btif in dts.
Signed-off-by: Elwin Huang <s09289728096@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20181
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit fixes stability issues on certain RAX3000Me devices. Some
devices has DDR3 RAM which don't able to work reliably at 2133 MHz
and require special BL2 (1866 MHz RAM freq).
Fixes: https://github.com/openwrt/openwrt/issues/20046
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20059
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Buffalo WSR-6000AX8 and AX8P models.
Hardware
--------
SOC: MediaTek MT7986B
RAM: 512MB
FLASH: 128MB SPI-NAND (Winbond)
WIFI 2.4G: (Embedded in SOC) b/g/n/ax, MIMO 4x4
WIFI 5G: (Embedded in SOC) a/n/ac/ax, MIMO 4x4
ETHERNET: 2.5GbE MaxLinear GPY211C (eth1: WAN)
ETHERNET: MediaTek MT7531AE 3xGbE (eth0: LAN1, LAN2, LAN3)
UART: 3.3V 115200 8N1
Serial(UART) Pin Layout
-----------------------
+-------+-------+-------+-------+
J4 | RX | TX | GND |(3.3V) |
+-------+-------+-------+-------+
(Bottom Side)
MAC Address Table
-----------------
lan1-3: board_data 0x4(text)
eth1/WAN: board_data 0x4(text)
WIFI 2.4G: lan1 + 2
WIFI 5G: lan1 + 9
Installation
------------
1. Set up a TFTP server with the IP address "192.168.11.2".
2. Rename the OpenWrt initramfs image to "linux.ubi-recovery" and place it
in the TFTP server's root directory.
3. While holding down the AOSS button, power on the WSR-6000AX8 (or AX8P).
4. The device will automatically download the initramfs image
from the TFTP server and boot into it.
5. Once booted, run "sysupgrade -n" using the OpenWrt sysupgrade image
to complete the installation.
Recovery
--------
1. Decrypt the official firmware image using "buffalo-enc".
example:
$ buffalo-enc -d -i wsr_6000ax8_jp_100 -o wsr_6000ax8_jp_100.dec \
-l -O 0xc8
2. Run "sysupgrade -F -n" with the decrypted image.
Signed-off-by: Shin Sato <shin.sugar.ssyysy2021@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/13107
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification :
- SOC : Mediatek MT7981B (1.3GHz)
- RAM : 256MB
- Flash : 16MB SPI NOR
- Ports : 4 LAN (1G) & 1 WAN (1G)
- WIFI : MediaTek dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Buttons : Reset & WPS/Mesh
- LEDS : WAN (Green), Status (Red & Blue)
- Power : 12V1A
Install via OEM web ui:
Upload the sysupgrade image to firmware upgrade page on OEM web ui
Install via recovery / revert to stock firmware:
1. Unplug from power
2. Download the Sysupgrade (for openwrt installation) or OEM Factory image (for revert to stock firmware)
3. Set your computer ethernet IP to 192.168.1.X, subnet 255.255.255.0 (X=your chosen ip number ranging from 2-254)
4. Press and hold reset button while turn on / plug power adapter to the router. Wait untill ALL LAN green LED turn on, then release the reset button.
5. Plug the LAN cable from your computer into LAN 1 port then open web browser, and type in the address column : 192.168.1.1
6. Upload the sysupgrade / oem factory image
7. Wait until the router finished flashing (the router will reboot)
8. Set ethernet ip to dhcp
9. Open 192.168.1.1 (for openwrt install) / 192.168.0.1 (for OEM firmware)
Signed-off-by: Ari Kurniawan <noobhek@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20035
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes a previous commit breaking setting the MAC address for the
wifi devices.
Fixes: 9ed4d27fbf ("mediatek: filogic: fix 5G MAC address for Zyxel EX5601")
Link: https://github.com/openwrt/openwrt/pull/20100
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
