Fixes the "mdio_bus stmmac-1: MDIO device at address 1 is missing" error
that occurs during cold boot when initializing GMAC.
Fixes: 8ca4caacd0 ("rockchip: Add support for RK3568 LinkEase EasePi R1")
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20772
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3528 ARM64 (4 cores)
1/2/4GB LPDDR4 RAM
1x LED (state)
1x Reset button
0/8/16/32/64GB eMMC on-board
Micro-SD Slot
PCIe FPC connector
3x USB 2.0 Port
HDMI/AV OUT
USB Type-C 5V Power
ROCK 2A:
+ 3.5mm audio out
+ 1000 Base-T
+ SYS LED
+ USB 3.0 Port (conflicts with PCIe)
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20375
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Unset KERNEL_LOADADDR in default profile to avoid using the value
from other boards (if someone forgets to set KERNEL_LOADADDR).
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20375
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit 8ca4caacd0 ("rockchip: Add support for RK3568 LinkEase EasePi R1")
forgot to include the SoC recipe, which leads KERNEL_LOADADDR undefined.
Fixes: 8ca4caacd0 ("rockchip: Add support for RK3568 LinkEase EasePi R1")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20722
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The probe order for PCIe buses and devices is non-deterministic,
making the names eth0 and eth1 unpredictable (they may be swapped).
This patch fixes the names by referencing the device path using
`ucidef_set_network_device_path`.
The mapping between silkscreen labels on the board/case and OpenWrt
interface names is as follows:
- E52C
LAN: lan
WAN: wan
- ROCK 5 ITX
RJ45 1: eth0
RJ45 2: eth1
- ROCK 5T
RJ45_1: eth0
RJ45_2: eth1
For Radxa E52C, this breaks compatibility of the network config;
therefore, set DEVICE_COMPAT_VERSION to `1.1`.
Fixes: d16d2765bd ("rockchip: add support for Radxa E52C")
Fixes: 0839345211 ("rockchip: add support for Radxa ROCK 5 ITX/ITX+")
Fixes: 4a78af9876 ("rockchip: add support for Radxa ROCK 5T")
Link: https://github.com/openwrt/openwrt/issues/20202
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/20608
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenWrt buildroot will compile all dtbs defined in target to
$(KDIR)/image-$(DEVICE_DTS).dtb, so make use of it to allow us
debug and use external dtbs easier without patching kernel Makefile.
This also fixes commit 5c724939c3 which forgot to update DTS_DIR
in KERNEL variable.
Fixes: 5c724939c3 ("rockchip: add DEVICE_DTS_DIR definition")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20286
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The FIT loadaddr on RK3308/RK3566/RK3568/RK358x is 0x02000000
instead of 0x02080000, while on RK3576 it's 0x42000000, which is
quite different from the former SoCs and incompatible with current
kernel loadaddr value.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20041
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
1/2GB LPDDR4 RAM
2x 2500 Base-T (PCIe, r8125b)
1 LED (Power)
1 Button (Reset)
Micro-SD Slot
2x USB 3.0 Port
12V DC Jack
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa E52C is a compact network computer using the Rockchip RK3582
SoC.
- https://radxa.com/products/network-computer/e52c
Hardware
--------
- Dual Cortex-A76 and Quad Cortex-A55 CPU
- 5 TOPS NPU
- 2/4/8GB LPDDR4 RAM
- 16/32/64GB on-board eMMC
- microSD card slot
- 2x 2.5 Gigabit Ethernet ports
- USB 3.1 Gen1 Type-A HOST/OTG port
- USB Type-C debug port
- USB Type-C power port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 5C (Lite) is a single board computer using the Rockchip
RK3588S2 (RK3582) SoC.
- https://radxa.com/products/rock5/5c
Hardware
--------
- Quad (Dual) Cortex-A76 and Quad Cortex-A55 CPU
- Mali-G610 MP4 GPU (5C only)
- 6 (5) TOPS NPU
- 1/2/4/8/16/32GB LPDDR4X RAM
- eMMC/SPI NOR flash connector
- microSD card slot
- Wi-Fi 6 (AIC8800D80, not yet supported)
- Gigabit Ethernet port with PoE (additional PoE HAT required)
- USB 3.1 Gen1 Type-A HOST/OTG port
- USB 3.1 Gen1 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- FPC connector with PCIe 2.1 x1
- PWM fan connector
- 20x2 pin header
- USB Type-C power port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 5 ITX(+) is a Mini-ITX form factor computer using the
Rockchip RK3588 SoC.
- https://radxa.com/products/rock5/5itx
- https://radxa.com/products/rock5/5itxp
Hardware
--------
- Quad Cortex-A76 and Quad Cortex-A55 CPU
- Mali-G610 MP4 GPU
- 6 TOPS NPU
- 4/8/16/24/32GB LPDDR5 RAM
- on-board eMMC
- 16MB SPI NOR flash
- microSD card slot
- 2x 2.5 Gigabit Ethernet ports with PoE (additional PoE module required)
- USB 3.1 Gen1 Type-C HOST/OTG port
- 4x USB 3.1 Gen1 Type-A HOST ports
- 2x USB 2.0 Type-A HOST ports
- M.2 M Key connector with PCIe 3.0 x2
- 4x SATA connectors (ITX only)
- 2nd M.2 M Key connector with PCIe 3.0 x2 (ITX+ only)
- M.2 E Key connector with PCIe 2.1 x1 and USB 2.0
- RTC battery socket for CR1220
- 4pin PWM fan connector
- Serial console pin header
- Front panel pin headers
- 24pin ATX power connector
- 5525 12V DC jack
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 5B+ is a single board computer using the Rockchip
RK3588 SoC.
- https://radxa.com/products/rock5/5bp
Hardware
--------
- Quad Cortex-A76 and Quad Cortex-A55 CPU
- Mali-G610 MP4 GPU
- 6 TOPS NPU
- 4/8/16/24/32GB LPDDR5 RAM
- 16/32/64/128/256GB on-board eMMC (optional)
- 16MB SPI NOR flash
- microSD card slot
- Wi-Fi 6 (Realtek RTW8852BE)
- 2.5 Gigabit Ethernet port with PoE (additional PoE HAT required)
- USB 3.1 Gen1 Type-C HOST/OTG port
- 2x USB 3.1 Gen1 Type-A HOST ports
- 2x USB 2.0 Type-A HOST ports
- 2x M.2 M Key connectors with PCIe 3.0 x2
- M.2 B Key connector
- SIM card slot
- RTC battery connector
- PWM fan connector
- 20x2 pin header
- USB Type-C power port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is a variant of the Radxa ROCK Pi E v3 equipped with the Realtek
RTL8821CU. Add the kmod-rtw88-8821cu package for it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/18310
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The board name that goes into /etc/board.json and is used by sysupgrade
for image verifications gets determined by the below command:
`strings /proc/device-tree/compatible | head -1`
as per package/base-files/files/lib/preinit/02_sysinfo
On more recent firmware version for the Pine64 RockPro64 v2.1 devices the
first entry is 'pine64,rockpro64-v2.1' however the metadata in the
sysupgrade image only specifies 'pine64,rockpro64' as supported and image
verification will fail.
This change makes it so the image metadata will contain both
'pine64,rockpro64' and 'pine64,rockpro64-v2.1' allowing image verification
to pass on both older and more recent firmware versions.
Signed-off-by: Sam Hegarty <hegarty.sam@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18542
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 4SE[1] is a single board computer using the Rockchip
RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- M.2 M Key slot (PCIe 2.1 x4)
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4se
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 4C+[1] is a single board computer with dual HDMI using
the Rockchip RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4cp
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the FriendlyElec NanoPi R3S.
CPU: Rockchip RK3566, Quad-core Cortex-A55
RAM: 2GB LPDDR4X
Ethernet: GMAC RTL8211F GbE, PCIe R8111H GbE
USB3.0 Host: Type-A x1
Storage: MicroSD Slot x 1, and optional on-board 32GB eMMC
Debug Serial Port: 3.3V TTL, 3-pin 2.54mm pitch connector, 1500000 bauds
LED: LED x 3
RTC: One low-power RTC, supports backup battery input
Both GbE controllers are working (WAN eth0, LAN eth1).
Appropriate LAN/WAN interface assignments and MAC address generation.
All three LEDs are working.
USB appears to be working and has been tested with mass storage.
Installation - microSD:
-Uncompress the OpenWRT sysupgrade.img.gz
-Write image to microSD card using dd or similar tool
Installation - eMMC:
-Boot from microSD
-Uncompress the OpenWRT sysupgrade.img.gz
-Flash to eMMC : dd if=x.img of=/dev/mmcblk0
-sync
-Remove microSD card
-Reboot
Signed-off-by: Kevin Zhang <kevin@kevinzhang.me>
Link: https://github.com/openwrt/openwrt/pull/16738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This board is also as known as Bananapi BPi-M7.
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
8/16/32GB LPDDR4/LPDDR4x RAM
2x 2500 Base-T (PCIe, rtl8125b)
2 LEDs (RED / GREEN)
16GB/32GB/64GB/128GB eMMC on-board
Micro-SD Slot
USB 2.0 Port
USB 3.0 Port
M.2 M-Key
40-Pin Header
USB PD 2.0 9/12/15V Power
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16462
Signed-off-by: Nick Hainke <vincent@systemli.org>
Hardware Spec
-SoC: Rockchip RK3588S
CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
-RAM: 64-bit 4GB/8GB LPDDR4X at 2133MHz
-Flash: 32GB/None eMMC, at HS400 mode
-Ethernet: one Native Gigabit Ethernet, and one PCIe 2.5G Ethernet
-USB: one USB 3.0 Type-A and one USB 2.0 Type-A
-PCIe: one M.2 Key M connector with PCIe 2.1 x1
-HDMI:
compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
support up to 7680x4320@60Hz
Support RGB/YUV(up to 10bit) format
-microSD: support up to SDR104 mode
-GPIO:
30-pin 2.54mm header connector
up to 1x SPI, 3x UARTs, 3x I2Cs, 2x SPDIFs, 1x I2Ss, 3x PWMs, 20x GPIOs
-Debug: UART via 3-Pin 2.54mm header, or on-board USB-C to UART
-LEDs: 4 x GPIO Controlled LED (SYS, WAN, LAN, LED1)
-others:
2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS
MASK button for eMMC update
one user button
-Power supply: USB-C, support PD, 5V/9V/12V/20V input
-PCB: 8 Layer, 62x90x1.6mm
-Ambient Operating Temperature: 0℃ to 70℃
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
eMMC Installation:
Boot from the SD card
Uncompress the OpenWrt sysupgrade image
fash to eMMC : dd if=*.img of=/dev/mmcblk1
sync
remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3B is a Pico-ITX form factor SBC[1] using the Rockchip
RK3568(J).
Hardware
--------
- Rockchip RK3568(J) SoC
- Quad A55 CPU
- Mali-G52 GPU
- 1 TOPS @ INT8 NPU
- 2GB/4GB/8GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key (2-lane PCIe 3.0)
- SPI Flash for bootloader
- 2x Gigabit ethernet port (one supports PoE with add-on PoE HAT)
- 1x M.2 E Key socket with SDIO, UART and USB interfaces
- 1x M.2 B Key socket with PCIe, SATA, and USB interfaces
- 1x SIM card socket
- 1x USB 3.0 Type-A HOST port
- 1x USB 3.0 Type-A OTG port
- 2x USB 2.0 Type-A HOST ports
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3b
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3C is a high-performance, low-cost SBC[1] using the
Rockchip RK3566.
Hardware
--------
- Rockchip RK3566 SoC
- Quad A55 CPU
- Mali-G52-2EE GPU
- 1 TOPS @ INT8 NPU
- 1GB/2GB/4GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key connector(2230) or M.2 Extension
board(2232/2260/2280)
- SATA through the Radxa Penta SATA HAT
- 1x Gigabit ethernet port(supports PoE with add-on PoE HAT)
- WiFi6/BT5.4 (not supported yet on OpenWrt)
- 1x USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- 1x USB 2.0 Type-A OTG port
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3c
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16/32GB LPDDR4X RAM
2500 Base-T
RGB LED
eMMC Connector
SPI-NOR 16MB
Micro-SD Slot
2x USB 2.0 Port
2x USB 3.0 Port
Headphone Jack
M.2 E-Key
M.2 M-Key
USB PD 5/9/12/15/20V Power
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16/32GB LPDDR4X RAM
1000 Base-T
Status LED
eMMC/SPI Connector
Micro-SD Slot
2x USB 3.0 Port
2x USB 2.0 Port
Headphone Jack
M.2 E-Key
USB PD/QC 5/9/12/15/20V Power
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SUPPORTED_DEVICES is required for Radxa ROCK Pi S.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16167
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patches for the nanopi r6s board, backporting from 6.9 where
basic support is landing.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes the image check failed on system upgrade
"Image check failed:
upgrade: Device radxa,rock3a not supported by this image
upgrade: Supported devices: radxa,rock-3a"
Signed-off-by: Tomas Lara <tl849670@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16064
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi E v3.0 has a RTL8723DU Wi-Fi 4 on-board device. enable
it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15910
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi S has a RTL8723DS Wi-Fi 4 on-board device. enable it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15910
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi E v3.0 is a compact networking SBC[1] using the Rockchip
RK3328 SoC.
Hardware
--------
- Rockchip RK3328 SoC
- Quad A53 CPU
- 512MB/1GB/2GB DDR4 RAM
- 4/8/16/32GB eMMC
- Micro SD Card slot
- WiFi 4 and BT 4, or WiFi 5 and BT 5 (not supported yet)
- 1x 1000M Ethernet with PoE support (additional PoE HAT required)
- 1x 100M Ethernet
- 1x USB 3.0 Type-A port (Host)
- 1x 4-ring 3.5mm headphone jack
- 40 Pin GPIO header
[1] https://radxa.com/products/rockpi/pie
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15984
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi S is a small in size, full in features SBC[1] using the
Rockchip RK3308B SoC.
Hardware
--------
- Rockchip RK3308B SoC
- Quad A35 CPU
- 256/512MB DDR3 RAM
- Optional 4/8GB eMMC
- Micro SD Card slot
- Optional WiFi 4 and BT 4 (not supported yet)
- 1x 100M Ethernet with PoE support (additional PoE HAT required)
- 1x USB 2.0 Type-A port (Host)
- 1x USB 2.0 Type-C port (OTG)
- 2x 26 Pin GPIO header
[1] https://radxa.com/products/rockpi/pis
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15933
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
use u-boot-rockchip.bin to copy SPL/TPL/U-Boot to the image.
since binman was used in mainline u-boot for rockchip, we can use
u-boot-rockchip.bin instead of idbloader.img and u-boot.itb.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15815
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware spec:
- Rockchip RK3568 Quad-core ARM Cortex-A55 CPU 2GHz
- GPU Mali-G52 1-Core-2EE OpenGL ES3.2 Vu1kn 1.1 OpenCL 2.0
- Memory2G DDR3 SDRAM (option 4G)
- Storage Onboard 16GB eMMC Flash, Micro SD-Card slot, SATA 3.0 Port,SPI flash
- Network 5 x 10/100/1000 Mbit/s Ethernet MT7531
- Display 1 HDMI port, 2 DSI interface(1 DSI can change to LVDS by software)
- Camera 1 CSI camera interface
- Audio Output HDMI & I2S & Speaker & Headphone
- USB port USB 3.0 PORT (x2), micro USB OTG (x1)
- PCIE 1 mini pcie interface & 1 M.2 key-e interface
- Remote IR Receiver (x1)
- GPIO 40 Pin Header : GPIO (x28) and Power (+5V, +3.3V and GND).
- Switches Reset button, Power button, U-boot button
- LED Power Status
- Power Source 12 volt 2A via DC Power
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
Boot from the SD card
1-hold down the MaskRom button
2-Connect DC power
3-Wait 5 seconds, release the button.
eMMC Installation:
1-Uncompress the OpenWrt sysupgrade image
2-fash to eMMC
dd if=openwrt-rockchip-armv8-sinovoip_bpi-r2-pro-squashfs-sysupgrade.img of=/dev/mmcblk1
sync
3-remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
ttyS2 is the default console used for all rockchip boards.
The redundant 'console=tty1' parameter now breaks the console due to
recent procd update.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
We have hardware IOMMU support and this is totally unnecessary.
The given value is also unreasonable, it's too small and causes
kernel panic in some cases:
[ 5706.856473] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 28672 bytes), total 512 (slots), used 498 (slots)
[ 5706.864451] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 65536 bytes), total 512 (slots), used 464 (slots)
This parameter seems to be added by mistake, so remove it.
Fixes: e35c7ab51f ("rockchip: merge bootscript")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Radxa E25 is a network application carrier board for the Radxa CM3
Industrial (CM3I) SoM, which is based on the Rockchip RK3568 SoC.
It has the following features:
- MicroSD card socket, on board eMMC flash
- 2x 2.5GbE Realtek RTL8125B Ethernet transceiver
- 1x USB Type-C port (Power and Serial console)
- 1x USB 3.0 OTG port
- mini PCIe socket (USB or PCIe)
- ngff PCIe socket (USB or SATA)
- 1x User LED and 16x RGB LEDs
- 26-pin expansion header
Installation:
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
