flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
- tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
- ubiattach -p /dev/mtd0
- ubirmvol /dev/ubi0 -n0
- ubirmvol /dev/ubi0 -n1
- ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
- sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin
Signed-off-by: John Crispin <john@phrozen.org>
This patch adds support for the Sercomm Kiwi AP.
Specification:
- SoC: Qualcomm Atheros IPQ807x ARM64 quad core
- RAM: 1GB
- NAND Flash: 256MB
- Ethernet: 1 x 2G
- WLAN: 2x Titan AX
Installation instructions:
1) scp openwrt-ipq807x-sercomm_kiwi-squashfs-nand-factory.bin into the preflashed qsdk image
2) ssh into the unit and call sysupgrade -n openwrt-ipq807x-sercomm_kiwi-squashfs-nand-factory.bin
Signed-off-by: John Crispin <john@phrozen.org>
This patch adds support for the Cigtech WF188 AP.
Specification:
- SoC: Qualcomm Atheros IPQ6018 ARM64 quad core
- RAM: 512MB
- NOR Flash: 32MB SPI NOR
- Ethernet: 1 x 1G
- WLAN: 2x IPQ60xx AX
Installation instructions:
1) enter uboot console
- setenv bootargs mtdparts=spi32766.0:6144k@3712k(0:HLOS),20608k@9856k(rootfs) console=ttyMSM0,115200n8
- tftpboot 0x44000000 wf188-initramfs
- bootm
2) inside the in ramfs, scp the sysupgrade image to the device and run sysupgrade.
Signed-off-by: John Crispin <john@phrozen.org>
Add openNDS package to enable captive portal at bridge level added customized
configurations to make it work as required Package:openNDS
Signed-off-by: Nagendrababu <nagendrababu.bonkuri@connectus.ai>
This feature makes use of the crashlog driver in the kernel. If we experience
an oops, the kernel will store the stack trace inside /sys/kernel/debug/crashlog.
OpenSync will then add an entry to the Alarms table. The could can then retrieve
the crashlog via the Command_config table.
A crash can be simulated with
echo c > /proc/sysrq-trigger
Signed-off-by: John Crispin <john@phrozen.org>
Once the AP connected to the cloud for the first time we wait 5 minutes.
Once that period is over we stop and disable the webserver. It is only
intended for initial WAN bringup during deployment.
Signed-off-by: John Crispin <john@phrozen.org>
This series is based on
* 2020-07-10 ipq6018-ilq-11-0_qca_oem-034672b0676c37b1f4519e5720e18e95fe6236ef
Add support for
* qsdk kernel/v4.4
* qsdk ethernet subsystem
* v5.7 ath11k backport + QualComm staging patches (wlan_ap_1.0)
* ath11k-firmware
* hostapd/iw/...
Feature support
* full boot, system detection
* sysupgrade to nand
* HE support via latest hostapd
* driver support for usb, crypto, hwmon, cpufreq, ...
Missing
* NSS/HW flow offloading - FW blob is not redistributable
Using the qsdk v4.4 is an intermediate solution while the vanilla is being
tested. Vanilla kernel is almost on feature par. Work has already started
to upstream the ethernet and switch drivers. Once complete the target will
be fully upstream.
Signed-off-by: John Crispin <john@phrozen.org>
This allows us to trigger remote commands, such as tcpdump.
Also allow configuring NTP and remote syslog.
Signed-off-by: John Crispin <john@phrozen.org>
Add new package which has scripts for ssid client ratelimiting.
Adds rules for ssid ratelimiting and client ratimiting based on
'wireless' config file options 'drate'(ssid dl), 'urate'(ssid ul),
'cdrate'(client dl), and 'curate' (client ul).
Signed-off-by: Chaitanya Kiran Godavarthi <chaitanya.kiran@connectus.ai>
This package will automatically include the cloud keys in the image.
- /usr/plume/certs/ca.pem
- /usr/plume/certs/client.pem
- /usr/plume/certs/client_dec.key
Signed-off-by: John Crispin <john@phrozen.org>
