1. Using rtl8367c.c file for rtl8367S switch driver to support vlan
2. Configure eth0.1 as WAN and eth0.2 as LAN
3. Add mdio read/write in smi driver followed 5.4 kernel driver
4. add mido clock setting followed 5.4 kernel driver for 186w board
5. Add eth and wifi mac address allocation based of BaseMacAddress
6. Update new bdf for 2G radio
Fixes: WIFI-12650
Signed-off-by: Ken <xshi@actiontec.com>
Mesh++ S618 has below products based on Qualcomm IPQ6018:
* cp03-c1
* cp01-c1
These are Wi-Fi 6 (IEEE 80211.ax) dual band 2x2 mesh routers.
Fixes: WIFI-10561
Signed-off-by: Krishna <krishna@meshplusplus.com>
Signed-off-by: Edward Cheung <edward@meshplusplus.com>
Signed-off-by: Alex Ballmer <alexb@meshplusplus.com>
Device specifications:
======================
* Qualcomm IPQ6000
* 512 MB of RAM
* 64 MB of SPI NOR flash
- 2x 28 MB available; but one of the 28 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11ax)
* 2T2R 5 GHz Wi-Fi (11ax)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board
* 2x ethernet
- eth0
+ 1000 Mbps Ethernet
+ used as LAN interface
- eth1
+ 1000 Mbps Ethernet
+ 802.3at POE
+ used as WAN interface
* 12 2A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
setenv bootargs 'console=ttyMSM0,115200n8 rootfstype=squashfs,jffs2 board=PAX1800v2 root=31:10 mtdparts=spi32766.0:768k(0:SBL1),64k(0:MIBIB),1664k(0:QSEE),64k(0:DEVCFG),128k(0:RPM),64k(0:CDT),64k(0:APPSBLENV),640k(0:APPSBL),256k(0:ART),28672k(inactive),28672k(inactive2),64k(custom),64k(0:KEYS),2304k(0:WIFIFW)'
tftpboot <filename-of-initramfs-kernel>.bin && bootm
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Because we have an another similar device named gl-axt1800,
so we put the common functions in a dtsi file. And we'll
submit a PR for gl-axt1800 soon.
Hardware:
* SoC: Qcom IPQ6000
* RAM: DDR3L 512MB
* Flash: 128MB Nand
* Ethernet: 5x GbE
* WLAN: 2x2 2.4GHz 600Mbps + 2x2 5GHz 1200Mbps (builtin + builtin)
* LEDS: 1x white, 1x blue
* Buttons: 1x switch, 1x reset
* USB: 1x 3.0(Type-A)
* Power: 12VDC, 1.5A
Installation:
* from qsdk to openwifi:
upgrade "openwrt-ipq807x-glinet_ax1800-squashfs-nand-factory.bin" via web ui
without keep config.
* upgrade "openwrt-ipq807x-glinet_ax1800-squashfs-sysupgrade.tar" if you are already in openwifi.
Signed-off-by: Jianhui Zhao <jianhui.zhao@gl-inet.com>
This caused image to pop up builds with no BDF in the image.
Fixes: 1a305421 (ipq807x: add support for wallystech dr6018)
Signed-off-by: John Crispin <john@phrozen.org>
* rename eap6x0 to exxx7
* update schema
* update client
* update gateway
* update usteer
* implement all missing ucentral commands
* patch the led script to allow turning of all leds
Signed-off-by: John Crispin <john@phrozen.org>
* fix dhcpsnoop on ipq807x
* update ucentralgw
* add eap620/660 support
* add cigwf610d
* do not deploy a default ratelimit config
* add eap225 support
Signed-off-by: John Crispin <john@phrozen.org>
