mirror of
https://github.com/hzyitc/openwrt-redmi-ax3000.git
synced 2025-12-17 17:03:27 +00:00
ramips: mt76x8: add support for Cudy RE1200 Outdoor v1
Hardware: - SoC: MediaTek MT7628DAN - Flash: 8 MiB XMC 25QH64CHIQ - RAM: 64 MiB (integrated on SoC) - WLAN: 2.4 GHz (MT7603E, 11n), 5 GHz (MediaTek MT7613BEN, 11ac) - Ethernet: 1x10/100 Mbps LAN - Buttons: 1 Reset button, 1 WPS button - LEDs: 5x Green - Serial Console: unpopulated header 115200 8n1 - Power: 24v Passive POE MAC addresses: +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | LAN | 80:af:ca:xx:xx:x0 | label | | WLAN 2g | 80:af:ca:xx:xx:x0 | label | | WLAN 5g | 80:af:ca:xx:xx:x2 | +2 | +---------+-------------------+-----------+ Installation: Please check the Wiki for this device for a more convenient solution than the one below. 1. Disassemble the device, desolder and dump the flash chip with a SPI programmer. 2. Separate the partitions with dd: dd if=spi_dump.bin of=u-boot.bin bs=1 skip=0 count=196608 status=progress dd if=spi_dump.bin of=u-boot-env.bin bs=1 skip=196608 count=65536 status=progress dd if=spi_dump.bin of=factory.bin bs=1 skip=262144 count=65536 status=progress dd if=spi_dump.bin of=firmware.bin bs=1 skip=327680 count=7995392 status=progress dd if=spi_dump.bin of=bdinfo.bin bs=1 skip=8323072 count=65536 status=progress 3. Download the sysupgrade firmware at openwrt.bin. 4. The firmware size should be 7995392 bytes. Fix the size of your firmware putting zeros to the end, with: truncate -s 7995392 firmware.bin 5. Combine all the parititions: cat u-boot.bin u-boot-env.bin factory.bin openwrt.bin bdinfo.bin > spi_new.bin 6. Erase and flash the SPI chip with the new file. Solder the chip and boot the router. Signed-off-by: Luis Mita <luis@luismita.com> Link: https://github.com/openwrt/openwrt/pull/20381 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
Luis Mita
Hauke Mehrtens
parent
1035615731
commit
65215e6d46
186
target/linux/ramips/dts/mt7628an_cudy_re1200-outdoor-v1.dts
Normal file
186
target/linux/ramips/dts/mt7628an_cudy_re1200-outdoor-v1.dts
Normal file
@ -0,0 +1,186 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "mt7628an.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
compatible = "cudy,re1200-outdoor-v1", "mediatek,mt7628an-soc";
|
||||
model = "Cudy RE1200 Outdoor v1";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_status;
|
||||
led-running = &led_status;
|
||||
led-failsafe = &led_status;
|
||||
led-upgrade = &led_status;
|
||||
label-mac-device = ðernet;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status:status {
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
};
|
||||
|
||||
internet {
|
||||
gpios = <&gpio 40 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WAN_ONLINE;
|
||||
};
|
||||
|
||||
lan {
|
||||
gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_LAN;
|
||||
};
|
||||
|
||||
wifi2g {
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN_2GHZ;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wifi5g {
|
||||
gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN_5GHZ;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <40000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x30000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "factory";
|
||||
reg = <0x40000 0x10000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory_0: eeprom@0 {
|
||||
reg = <0x0 0x400>;
|
||||
};
|
||||
|
||||
eeprom_factory_8000: eeprom@8000 {
|
||||
reg = <0x8000 0x4da8>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x50000 0x7a0000>;
|
||||
};
|
||||
|
||||
partition@ff0000 {
|
||||
label = "bdinfo";
|
||||
reg = <0x7f0000 0x10000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_bdinfo_de00: macaddr@de00 {
|
||||
compatible = "mac-base";
|
||||
reg = <0xde00 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&state_default {
|
||||
gpio {
|
||||
groups = "i2c", "gpio", "wdt", "p0led_an", "wled_an";
|
||||
function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
wifi@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
nvmem-cells = <&eeprom_factory_8000>, <&macaddr_bdinfo_de00 2>;
|
||||
nvmem-cell-names = "eeprom", "mac-address";
|
||||
ieee80211-freq-limit = <5000000 6000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cells = <&eeprom_factory_0>, <&macaddr_bdinfo_de00 0>;
|
||||
nvmem-cell-names = "eeprom", "mac-address";
|
||||
};
|
||||
|
||||
ðernet {
|
||||
nvmem-cells = <&macaddr_bdinfo_de00 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&esw {
|
||||
mediatek,portmap = <0x3d>;
|
||||
mediatek,portdisable = <0x3e>;
|
||||
};
|
||||
@ -210,6 +210,17 @@ define Device/cudy_m1200-v1
|
||||
endef
|
||||
TARGET_DEVICES += cudy_m1200-v1
|
||||
|
||||
define Device/cudy_re1200-outdoor-v1
|
||||
IMAGE_SIZE := 7808k
|
||||
DEVICE_VENDOR := Cudy
|
||||
DEVICE_MODEL := RE1200 Outdoor
|
||||
DEVICE_VARIANT := v1
|
||||
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7663-firmware-ap
|
||||
UIMAGE_NAME := R56
|
||||
SUPPORTED_DEVICES += R56
|
||||
endef
|
||||
TARGET_DEVICES += cudy_re1200-outdoor-v1
|
||||
|
||||
define Device/cudy_tr1200-v1
|
||||
IMAGE_SIZE := 15872k
|
||||
DEVICE_VENDOR := Cudy
|
||||
|
||||
@ -113,6 +113,7 @@ tplink,archer-mr200-v6)
|
||||
ucidef_set_led_netdev "lan" "lan" "white:lan" "eth0"
|
||||
ucidef_set_led_netdev "wan" "wan" "white:wan" "wwan0"
|
||||
;;
|
||||
cudy,re1200-outdoor-v1|\
|
||||
mercusys,mb130-4g-v1|\
|
||||
tplink,re200-v2|\
|
||||
tplink,re200-v3|\
|
||||
|
||||
@ -195,6 +195,7 @@ ramips_setup_interfaces()
|
||||
"0:lan" "1:lan" "2:lan" "3:lan" "6t@eth0"
|
||||
ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi"
|
||||
;;
|
||||
cudy,re1200-outdoor-v1|\
|
||||
tplink,tl-mr3020-v3)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:lan" "6@eth0"
|
||||
|
||||
Loading…
Reference in New Issue
Block a user