Add support for changing mcast and beacon rate
in opensync for ath11k
Add debugfs entry for ath11k driver to set mcast,
beacon and mgmt rate.
For help:
cat /sys/kernel/debug/ieee80211/phyX/ath11k/set_rates
Eg: Set beacon rate to 12Mbps for iface wlan0 5G band
echo "wlan0 beacon 5 0x10000002" > /sys/kernel/debug/ieee80211/phy0/ath11k/set_rates
Signed-off-by: Chaitanya Godavarthi <chaitanya.kiran@netexperience.com>
The TP-Link device mounts the production_info partition, and apnos will
access the manufacturing data and copy the certificate to its use when
it is first booted.
Signed-off-by: Arthur Su <arthur.su@tp-link.com>
wifi-2984: tplink device mount manufacturing data and certificates
The EX227 and EX447 devices are added ath11k_generate_macs method.
Signed-off-by: Arthur Su <arthur.su@tp-link.com>
Switch to a DFS channel by RRM failed
since cac was not being run. We set the Beacon
CSA IE and reload the interface with new channel.
Signed-off-by: Chaitanya Godavarthi <chaitanya.kiran@netexperience.com>
Inconsistency(gaps in reporting) was noticed when metrics were observed
for 24 hours.
Root Cause: One of the sockets created and used in SM for periodic network-probe reporting
was not getting closed. Due to this system wide limit for maximum open file descriptors
was getting exhausted over a period of time and thus not allowing to create any more
sockets to send data.
Signed-off-by: Yashvardhan <yashvardhan@netexperience.com>
1. Set HT VHT HE based on the hw_mode
2. Set secondary frequency (center_freq1) based on bandwidth
3. Add HE parameter in ubus call switch_chan
Signed-off-by: Chaitanya Godavarthi <chaitanya.kiran@netexperience.com>
Under Bridged mode of configuration, when creating VLAN interface,
we create VLAN for both WAN and LAN side, whereas LAN side VLAN is
not requried.
Signed-off-by: ravi vaishnav <ravi.vaishnav@netexperience.com>
This Patch fixes leds incorrect service state issue, and correct the
label names for all wifi6 APs
Signed-off-by: Nagendrababu <nagendrababu.bonkuri@connectus.ai>
The EC420 reset button don't work, so it cannot be restarted or restored
to factory settings. The reset button is fixed to gpio18.
Signed-off-by: Arthur Su <arthur.su@tp-link.com>
- Currently ath10/11k reports time_bss_rx (amount of time the radio spent receiving data on a local BSS)
inside time_rx (amount of time the radio spent receiving data). This patch fixes the behavior.
- Added support to report time_bss_rx over nl80211
Signed-off-by: Yashvardhan <yashvardhan@netexperience.com>
Channel time, busy and other survey counters are showing incorrect values (less than previous or sometimes zero).
Consecutive survey dumps are expected to return monotonically increasing counter values.
Root Cause:
Clear on read in ath10k was leading to this issue.
Solution: Use the non-clearing
WMI_BSS_SURVEY_REQ_TYPE_READ wmi_bss_survey_req_type
Note: ath11k already has this fix.
Patch also fixes the utilization percentage calculation for different survey parameters in opensync
Signed-off-by: Yashvardhan <yashvardhan@netexperience.com>
Sometimes we see a Client session created with sessionId=0,
and this never gets deleted. The AP keep on sending this event
as long as it exist in the events list.
SessionId=0 is invalid. Adding checks to avoid creating session
with Id=0. Also added a check in the opensync ubus to skip
already processed events.
Signed-off-by: ravi vaishnav <ravi.vaishnav@netexperience.com>
Add rrm channel setting through radio config. This
allows channel change through radio config in the
case where vif is not reloaded.
The below commit disables reload of vif when setting
RRM parameters:
"wifi-2648:Config RRM params without wifi vif reload"
Signed-off-by: Ammad Rehmat <ammad.rehmat@connectus.ai>
Signed-off-by: Chaitanya Godavarthi <chaitanya.kiran@netexperience.com>
Configure the following without vif reload:
Tx power
probe_response_threshold
client disconnect threshold
Beacon and multicast rates
Signed-off-by: Chaitanya Godavarthi <chaitanya.kiran@netexperience.com>
wifi6 AP does not forward broadcast ARP request sent from one wifi
client to another wifi client. Enable proxy arp by default to have the
AP respond to ARP requests on behalf of the client.
Signed-off-by: Arif Alam <arif.alam@netexperience.com>
Merging from uCentral-trunk.
The switch in the IPQ807x/IPQ60xx devices will automatically learn the mac
addresses behind a port. But it will not unlearn this entry when some mac
switches from the ethernet port to the CPU port. This will for example
happens when a device roams from on AP to another AP. At least when both
are APs are bridging the wifi traffic directly or indirectly (mesh) to the
same ethernet broadcast domain.
As result, the roaming device can no longer receive any ethernet packets
which the AP is expected to receive on the ethernet port. This state will
be kept for a couple of minutes until the entry in the FDB is dropped
automatically. But it is still possible for the wifi device to send data
via the ethernet during this whole time.
One solution is to just disable learning on all ports. The other option
would be to enable the qca bridge-mgr which takes care of gathering the
events from the bridge and forwards it to the qca-ssdk (to manipulate the
state of the switch). The latter option was chosen to follow the approach
which QCA is also using in their QSDK.
Signed-off-by: ravi vaishnav <ravi.vaishnav@netexperience.com>
This patch will add the conditions to respond captive portal API's to
only valid configuration
Signed-off-by: Nagendrababu <nagendrababu.bonkuri@connectus.ai>
Mismatch in vifC and vifS for captive portal is
leading to opennds restarts and memory leakage.
Fix by making sure the vifC and vifS are in parity.
uci_blob not being freed, fix by making uci_blob
as global so that it need not be freed and can
be reused instead.
Signed-off-by: Chaitanya Godavarthi <chaitanya.kiran@netexperience.com>
Cleaning up captive portal code to improve stability and reduce memory leaks
Signed-off-by: Nagendrababu <nagendrababu.bonkuri@connectus.ai>
- During the configuration process, AP was triggering network
and wireless reload multiple times in a very short window
resulting in a poorly configured hostapd. This patch makes sure
that network/wireless is reloaded only once after all the configuration
is committed to UCI files.
Signed-off-by: Yashvardhan <yashvardhan@netexperience.com>
When the manufacturer block does not contain the model info,
it is then extracted from /tmp/sysinfo/board_name, stripped
off the manufacturer name and converted for all upper case string.
Signed-off-by: ravi vaishnav <ravi.vaishnav@netexperience.com>
Applying the user configured dwell time for off-channel scan
requests. This needed driver changes to accommodate the command/event
processing time in the configured scan timeout, otherwise the scan
is aborted resulting in no off-channel survey results.
Signed-off-by: ravi vaishnav <ravi.vaishnav@netexperience.com>
This fix applies to EA8300, WF194c and EAP102. For these APs,
the br-wan is mapped to eth1 instead of eth0. Adding fix to
use the mac address from eth1 as ID for these particular APs.
Signed-off-by: ravi vaishnav <ravi.vaishnav@netexperience.com>
This patch will change the label names for WiFi6 APs to follow common naming convention
Signed-off-by: Nagendrababu <nagendrababu.bonkuri@connectus.ai>
